manualshive.com logo in svg

Amprobe AM-140, User Manual, Page: 12 / 20

Share
Download
Amprobe AM-140 User Manual Download Page 12

 

11 

MAX/MIN RECORDING mode 

Press 

REC

 button momentarily to activate MAX/MIN recording mode. The LCD symbol 

“R” and “MAX MIN”

 

turn on. The meter beeps when new maximum or minimum reading 

is updated. Press the button momentarily to read throughout the Maximum (MAX), 

Minimum (MIN), and Maximum minus Minimum (MAX-MIN) readings. Press the button 

for 1 second or more to exit MAX/MIN recording mode. Auto Power Off feature will be 
disabled automatically in this mode. 

 

CREST

 

Capture (Instantaneous Peak Hold) mode 

Press 

CREST

 button momentarily to activate CREST mode to capture voltage or 

current signal duration as short as 0.8ms. This mode is available in DC, AC, DC+AC 
modes of voltage and current functions. The LCD symbols “C” & “MAX”

 

turn on. The 

meter beeps when new maximum or minimum reading is updated. Press the button 

momentarily to read throughout the Maximum (MAX), Minimum (MIN), and Maximum 

minus Minimum (MAX-MIN) readings. Press the button for 1 second or more to exit 
CREST capture mode. Auto Power Off feature will be disabled automatically in this 

mode. 

 

 

Relative Zero mode 

Relative Zero allows the user to offset the meter consecutive measurements with the 
displaying reading as the reference value. Practically MAX/MIN recording feature 

readings can also be set as relative reference value. Press the 

 button momentarily 

to activate and to exit Relative Zero mode. 

 

500000 high resolution stable mode 

In DC voltage and frequency functions, press the 

500000

 button momentarily to toggle 

between the 4-4/5 digits fast mode and the 5-4/5 digits high resolution stable mode. 

 

Backlighted display 

Press the 

SELECT

 button for 1 second or more to turn on or off the display backlight 

function. It will also be turned off automatically after 30 seconds to extend battery life. 

 

Manual or Auto-ranging 

Press the 

RANGE

 button momentarily to select manual-ranging mode, and the meter 

will remain in the range it was in, the LCD symbol 

  turns off. Press the button 

momentarily again to step through the ranges. Press and hold the button for 1 second 

or more to resume auto-ranging mode. 

Note: Manual ranging mode feature is not available in Hz function. 

Summary of Contents for AM-140





















Reviews:

No comments