background image

Amiad USA Ltd.

Tel: 704.662.3133

E-mail: [email protected]

120-J Talbert Road

Fax: 704.662.3155

Web: www.amiad.com

Mooresville, NC 28117

[email protected]

A

MIAD

L

IMITED

W

ARRANTY

made with respect to Products specified in invoice no. ______________

1.

This  certificate  applies  to  Amiad  Products  purchased  by ______________ (“

Purchaser

”).  This  limited  warranty  extends  only  to  the  original

purchaser, and is not transferable to anyone who subsequently purchases, leases, or otherwise obtains the Product from the original purchaser.

2.

Amiad hereby warrants that the Products are and will be free from defects in material and workmanship under normal use and service. Amiad

warrants that it will correct manufacturing defects in the Products, in accordance with the conditions set out in this warranty.

3.

This warranty is enforceable for a period of 12 months as of the date Bill of Lading or equivalent (the “

Warranty Period

”).

4.

In the event that  during the Warranty Period the Purchaser discovers a defect in material and/or workmanship in any Product or part (the

Defective Product

”), it shall submit a written complaint to Amiad using Amiad's standard customer complaint form. For the receipt of the

customer complaint form, the submissions of the complaint or any questions please contact your customer service representative.

5.

Upon written demand by Amiad the Purchaser shall return the Defective Products – or a sample thereof – to Amiad, at Amiad's cost. If the

customer ships any such Product, Amiad suggests the customer package it securely and insure it for value, as Amiad assumes no liability for any

loss or damage occurring during shipment. Provided however that in the event Amiad determines that the warranty does not apply to such

Product,  Purchaser  shall  promptly  reimburse  Amiad  for  such  cost  (including  freight  and  customs). Any returned  Product  or  part  must  be

accompanied by the warranty certificate and the purchase invoice. It is clarified that the Purchaser may not return the Defective Product unless

such return was coordinate and approved by Amiad in advance.

6.

Amiad's obligation under this warranty shall be limited to, at its option, the repair or exchange, free of charge, of the Product or any part which

may prove defective under normal use and service during the Warranty Period. The provision of a repaired or replacement Product during the

Warranty Period will result in an extension of the Warranty Period by an additional period of 12 months, provided that the total accumulated

Warranty Period shall in any event be no more than 18 months.

7.

This warranty is valid on the condition that the Products are installed according to Amiad's instructions as expressed in Amiad's instruction

manuals and according to the technical limitations as stipulated in Amiad's literature or as stated by a representative of Amiad.

8.

This warranty will not apply to damaged or defective Products resulting from or related to:
(i)

Fire, flood, power surges or failures or any other catastrophe/and or unforeseen occurrence, such as but not limited to those for which

the customers are customarily insured;

(ii)

Fault, abuse or negligence of the customer;

(iii)

Customer's responsibilities, including the failure of the intake water to meet the agreed standards, as set forth in a written document,

approved by Amiad or improper storage.

(iv)

Improper or unauthorized use of the Product or related parts by the customer, including the customer’s failure to operate the Product

in conformity with the recommendations and instructions of Amiad, as set forth in Amiad's manuals and other written materials, the

operation of the Product other than by a trained and qualified operator, or improper installation of the Product by a third party not

authorized by Amiad;

(v)

Performance by the customer of maintenance and other services other than by a trained and qualified advanced operator, or other

than in conformity with the recommendations and instructions of Amiad, or other than in accordance with procedures defined in the

literature supplied for Products;

(vi)

Any  alteration,  modification  foreign  attachment  to  or  repair  of  the  Products,  other  than by  Amiad  or  its  authorized  technical

representatives.

9.

In  no  event  shall  Amiad  be  liable  to  the  customer  or  any  third  party  for  any  damages,  including  indirect,  special,  exemplary, punitive  or

consequential damages, or lost profits arising out of or in connection with this warranty, or arising out of or in connection with the Product's

performance or failure to perform, even if it has been advised of the possibility of such damages.

10.

Amiad  will  be  excused  for  failure  to  perform  or  for  delay  in  performance hereunder  if  such  failure  or  delay  is  due  to  causes  beyond  its

reasonable control or force majeure preventing or hindering performance.

11.

The  limited  warranty  set  forth  herein  is  the  only  warranty  given  by  Amiad  and  is  provided  in  lieu  of  any  other  warranties  created  by  any

documentation, packaging or otherwise.

12.

Amiad makes no warranty whatsoever in respect of accessories or parts not supplied by Amiad. In the event that Amiad is required to correct a

defective Product or product not covered by this warranty, it will do so solely in consideration for additional fees.

33 of 34

Summary of Contents for ICS-TCP Series



































Reviews: