American Water Heater DIRECT VENT GAS WATER HEATER Installation And Operating Instruction Manual Download Page 2 | Manualshive

Page: 2 / 40

background image

2

CONGRATULATIONS!

You have just purchased one of the finest water heaters
on the market today!

This installation, operation and instruction manual will
explain in detail the installation and maintenance of your
new Direct Vent Gas Water Heater. We strongly
recommend that you contact a plumbing professional for
the installation of this water heater.

We require that you carefully read this manual, as well as
the enclosed warranty, and refer to it when questions
arise. If you have any specific questions concerning
your warranty, please consult the plumbing professional
from whom your water heater was purchased. For your
records we recommend that you write the model, serial
number and installation date of your water heater in the
maintenance section in the back of this manual.

This manual should be kept with the water heater.

We’re committed to providing you with the finest water
heater made.

«
1
2
3
4
...
»

Summary of Contents for DIRECT VENT GAS WATER HEATER









































Reviews:

No comments

Related manuals for DIRECT VENT GAS WATER HEATER

Brand: Haier Pages: 2

Brand: laguna Pages: 24

Brand: Navien Pages: 108

Brand: abc Pages: 8

Brand: abc Pages: 12

Brand: L.B. White Pages: 108

Brand: L.B. White Pages: 28

Brand: L.B. White Pages: 68

Brand: L.B. White Pages: 34

Brand: L.B. White Pages: 28

Brand: L.B. White Pages: 4

Brand: Lasko Pages: 4

Brand: ULTIMATE SPEED Pages: 52

WELCH DUOSEAL 1397C-46

Brand: Gardner Denver Pages: 28

Brand: Jecod Pages: 3

BEST ONE Series

Brand: EBARA Pages: 7

Brand: Cadet Pages: 16

Brand: EQUATION Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands