manualshive.com logo in svg

American Dynamics ADODHCL, Installation And Service Manual, Page: 9 / 20

Share
Download
American Dynamics ADODHCL Installation And Service Manual Download Page 9

AD DELTADOME OUTDOOR HOUSING
8000-2616-04, Rev. B

INSTALLATION AND SERVICE GUIDE

9

6.  Connect relay output, if used, to connector

P3 on PC board.

Pin

Color

Description

1

N/A

Normally Open (3.5mA sink)

2

N/A

Common

3

N/A

Normally Closed

7.  Connect remaining cables to PC board:

−

  Heater cable to connector P2

−

  Fan cable to connector P5

−

  3-pin ac plug to connector P7.

8.  Reattach environmental PC board

(Figure 11).

a.  Push board up toward base. As you do,

snake wires over top of base and form a
loop along side of housing opposite heater
assembly.

!

WARNING!

Keep cables entering housing
away from heater assembly.

b.  Align ground pad on PC board with access

hole above and insert board under spring
fingers. Board is keyed; it will only fit in
base one way. Press on dust cover to snap
board in place.

9.  Apply power to environ. PC board.

Figure 11. Reattaching PC board

 

Dust Cover

Environmental
PC Board

Align ground
pad with hole

Spring
Fingers

Base
(inside
housing)

Summary of Contents for ADODHCL





















Reviews:

No comments