manualshive.com logo in svg

American Dynamics ADODHCL, Installation And Service Manual, Page: 8 / 20

Share
Download
American Dynamics ADODHCL Installation And Service Manual Download Page 8

8

INSTALLATION AND SERVICE GUIDE

AD DELTADOME OUTDOOR HOUSING

8000-2616-04, REV. B

PC Board Setup

!

WARNING! Turn power off.

Turn off power at the source before
beginning this procedure.

CAUTION:

 Hold environmental PC board by its

edges to protect it from static electricity. Do not
remove its dust cover.

CAUTION:

 Connectors on PC board can be easily

broken! Use a 2.5mm (0.1") slotted screwdriver.
Wider blade widths can damage connectors. DO
NOT over tighten connector screws.

Performing following steps (refer to Figure 10).

1.  Touch metal housing to discharge static

electricity.

2.  Set termination jumper on PC board.

 

If comm. lines continue to another dome, place
jumper JW1 across pins 1–2 for “unterminated”.
If comm. lines do not continue, place jumper
JW1 across pins 2–3 for “terminated”.

3.  Connect BNC connector to pig-tailed video

input of PC board.

 

Before you connect, slide tubing [c] over video
cable. After you connect, slide tubing com-
pletely over BNC connectors for a snug fit.

 

CAUTION:

 Tubing keeps metal BNC connector

from contacting metal housing where it can
short out and damage electronics.

4.  Connect data to connector P1 on PC board.

Note: 

Wire colors are for composite cable only.

Manchester data connections to P1.

 Order

data cable 88760 (plenum) or 8760 (non-
plenum) from Belden by calling
1-800-235-3361.

Pin

Color

Designation

1-4

—

Not used.

5

Black

Manchester (+)

6

White

Manchester (–)

RS422 Data connections to P1

Pin

Color

Designation

1

Orange

RS422 Data In High (+)

2

Green

RS422 Data In Low (–)

3

Yellow

RS422 Data Out High (+)

4

Brown

RS422 Data Out Low (–)

5-6

—

Not used.

SensorNet Data Connections to P1

Pin

Color

Designation

1-4

—

Not used.

5

Brown

SensorNet (unshielded)

6

Yellow

SensorNet (unshielded)

5.  Connect alarm input, if used, to connector

P4 on PC board.

Pin

Color

Designation

1

N/A

Alarm input (3.5mA sink)

2

N/A

Ground

Figure 10. PC board connections

1

P1

P4

P3

JW1

NC

A0

1

NO

C

RTN

P2

P5

P7

AC

GND

AC

Alarm

JW1

Comm.

Relay
Output

AC

Heater

Fan

Base
(inside
housing)

Video BNC Connection

(cover with heat shrink tubing)

Environmental
PC Board

Summary of Contents for ADODHCL





















Reviews:

No comments