manualshive.com logo in svg

American Dynamics ADODHCL, Installation And Service Manual, Page: 16 / 20

Share
Download
American Dynamics ADODHCL Installation And Service Manual Download Page 16

16

INSTALLATION AND SERVICE GUIDE

AD DELTADOME OUTDOOR HOUSING

8000-2616-04, REV. B

Ordering Parts

This section helps you to identify parts that make
up the outdoor housing assembly. See table
opposite and Figure 18 for parts breakdown.

Note:

 Although all parts are shown, only parts

shown in bold can be ordered:

•

  Clear bubble assembly 0400-0928-01

•

  Smoked bubble assembly 0400-0928-02

•

  Fan/Heater assembly 0500-8023-01

•

  Environmental board 0301-0949-01

Order parts through your parts distribution network.
If a part to be repaired is other than those listed
above, the entire housing must be ordered.

To return parts to the National Service Center
(NSC), call one of the following numbers for a
repair authorization.

1-800-543-9740 (CEs)

1-800-442-2225 (Dealers)

1-800-241-6678 (End Users).

Parts list

 

1 Muffler

1400-0146-01

 

2 

Cable Assy., Fan*

0650-2000-01

 

3 Heater

0500-8023-01

 

4 Lanyard

0500-8797-01

 

5 Drive, 

Tamperproof

1400-0149-01

 

6 

Setscrew, M3x8 (Qty. 2)

5802-4055-320

 

7 

Elbow, 1-1/2 NPT

0500-8078-01

 

8 

Nut, 1-1/2 NPT

6010-0100-01

 

9 Cap

0500-8001-01

 

10 Sun 

Shield

0500-7954-01

 

11 

Nut, M6 (Qty. 4)

5826-0500-020

 

12 

Washer (Qty. 4)

5890-0500-020

 

13 Plate

0500-8051-01

 

14 Gasket

0500-7963-02

 

15 Housing

0500-7955-01

 

16 Thumbnut, 

M3

5899-0068-02

 

17 Gasket

0500-7963-02

 

18 Connector

6010-0097-01

 

19 Bracket

0500-8054-01

 

20 Fan/Heater 

Assy.

0400-0935-01

 

21 

Screw, M3x8, PH (Qty. 2)

5801-1051-120

 

22 Base

0500-8049-01

 

23 

Nut, M3 (Qty. 2)

5826-0200-020

 

24 

Environmental PC Board

0301-0949-01

 

25 Bubble 

Assy.

0400-0298
-01 (Clear)/
-02 (Smoked)

 

26 Gasket

0500-7963-01

 

27 Bubble

0500-7962
-01 (Clear)/
-02 (Smoked)

 

28 Trim 

Ring

0500-7956-01

 

29 

Screw, Tamperproof (Qty. 4)

0500-8034-01

* Part of Fan/Heater Assembly 0400-0935-01.

Summary of Contents for ADODHCL





















Reviews:

No comments