manualshive.com logo in svg

American Dynamics ADODHCL, Installation And Service Manual, Page: 13 / 20

Share
Download
American Dynamics ADODHCL Installation And Service Manual Download Page 13

AD DELTADOME OUTDOOR HOUSING
8000-2616-04, Rev. B

INSTALLATION AND SERVICE GUIDE

13

Troubleshooting Outdoor

Domes

Perform the following procedures if one of the
following symptoms occur:

−

  Dome does not respond to commands

−

  Fans do not turn

−

  Picture grainy or discolored

−

 Poor 

video

−

  Ice forms on bubble.

Dome Does Not Respond to
Commands

Follow steps until the problem is corrected. See
page 16 to order parts.

1.  Disconnect dome from base and examine

address switches.

 

Are they set correctly?

−

 YES: 

Continue.

−

  NO: Set correct address and reconnect

housing and eyeball assembly.

2.  Verify power is reaching housing.

 

Press and hold switch SW2 on environmental
PC board and observe the green (ac power)
LED. Does green LED glow steadily?

−

  YES: Reconnect housing and eyeball

assembly and continue.

−

  NO: Check power at J-box and ac cable

connections at connector P7 on other side
of environmental PC board. If these items
are OK, replace environmental PC board.

Connector P7 pin outs

Pin

Color

Description

1

N/A

24 Vac

2

N/A

Common

3

N/A

24 Vac

 

CAUTION:

 Screws on ac connector are

delicate. DO NOT over tighten them! Use a
2.5mm (0.1") slotted screwdriver. Wider
blade widths can damage connectors.

3.  Verify data is reaching housing.

 

SENSORNET or RS422: Press and hold switch
SW2 on environmental PC board and observe
yellow (comm.) LED. Yellow LED should blink
(SensorNet) or glow steadily (RS422). For test
switch location, see Figure 12.

 

To verify RS422 connections at connector P1,
press and hold data test switch SW1 on
environmental PC board. For test switch
location, see Figure 12. Observe nearby red
and green LEDs; they indicate the following:

Constant green,
Blinking red

RS422 line is correctly
wired.

Constant green,
No red

RS422 “Data In –” is
shorted to ground.

Constant red,
Blinking green

“Data In + /–” wires are
reversed.

Blinking red,
Green off

“Data In +” is shorted to
ground.

Both LEDs off

“Data In +/–” wires are
shorted or open.

P1 pin outs:

Manchester data connections

Pin

Color

Designation

1-4

—

Not used.

5

Black

Manchester (+)

6

White

Manchester (–)

RS422 Data connections

Pin

Color

Designation

1

Orange

RS422 Data In High (+)

2

Green

RS422 Data In Low (–)

3

Yellow

RS422 Data Out High (+)

4

Brown

RS422 Data Out Low (–)

5-6

—

Not used.

Summary of Contents for ADODHCL





















Reviews:

No comments