background image

Please Note:

 Specifications and improvements in the design 

of this unit and this manual are subject to change without any 
prior written notice.

 X-Move LED Plus R  

                               Specifications

Model:    

 

X-Move LED Plus R

Voltage*:

 

 

 

120v/60Hz or 230v/50Hz 

 

LED:   

 

 

1x10W LED

Power Consumption: 

60W

Dimensions: 

 

 

8”(L) x 7.5”(W) x 12.5”(H)

 

 

 

 

205mm x 190mm x 320mm

Beam Angle:   

 

14 Degree

Colors:

 

 

 

RGB + White

Weight:

 

 

 

13 Lbs. / 5.9 kgs.

Fuse:

   

 

 

2 Amp

Duty Cycle:

   

 

None

DMX: 

 

 

  

9 DMX Channels

Colors: 

 

 

8 + White

Gobos:

 

 

 

6 + Spot

 

 

 

 

23.8mm/0.2mm thickness

 

 

 

 

(19mm viewable)

Sound Active:

 

 

Yes

Working  Position:

   

Any Safe, Secure Position

Warranty:

 

 

 

3 Year (1095 days)

*Voltage is preset at the factory and is not user selectable

American DJ

®

 

American DJ World Headquarters:

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.americandj.com / E-mail: [email protected]

American DJ Europe

Junostraat 2

6468 EW Kerkrade

Netherlands

[email protected] / www.americandj.eu

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99

American DJ

®

  -  www.americandj.com  - X-Move LED Plus R Instruction Manual Page 23

Summary of Contents for X-Move LED Plus R













Reviews: