background image

  Vortex 1200                                            Fuse Replacement

  Vortex 1200                                                           Cleaning

Due to fog residue, smoke, and dust cleaning the internal and exter-

nal  optical  lenses  and  mirror  should  be  carried  out  periodically  to 

optimize  light  output.  Cleaning  frequency  depends  on  the  environ-

ment  in  which  the  fixture  operates  (I.e.  smoke,  fog  residue,  dust, 

dew). In heavy club use we recommend cleaning on a monthly basis. 

Periodic cleaning will ensure longevity, and crisp output.
1.  Use normal glass cleaner and a soft cloth to wipe down the out- 

  side casing.

2.   Use a brush to wipe down the cooling vents and fan grill.

3.   Clean the external optics with glass cleaner and a soft  cloth every  

  20 days.

4.   Clean the internal optics with glass cleaner and a soft cloth every  

  30-60 days.

5.  Always be sure to dry all parts completely before plugging the unit  

  back in.

Listed below are a few common problems the user may encounter, 

with solutions.
Unit not responding to DMX:
1.  Check that the DMX cables are connected properly and are    

  wired correctly (pin 3 is “hot”; on some other DMX devices    

  pin 2 may be ‘hot’). Also, check that all cables are connected   

  to the right connectors; it does matter which way the inputs    

  and outputs are connected.
Unit does not respond to sound:
1.  Quiet or high pitched sounds will not activate the unit.

2.  Check the sound sensitivity level.

  Vortex 1200                                               Troubleshooting 

Disconnect the unit from its power source. Locate the fuse holder on 

the rear panel of the unit. Using a phillips-head screw driver unscrew 

the fuse holder. Remove the bad fuse and replace with a new one. 

Screw the fuse holder back into the unit containing the new fuse.

ADJ Products, LLC  -  www.adj.com  - Vortex 1200 User Manual Page 31

ADJ Products, LLC  -  www.adj.com  - Vortex 1200 User Manual Page 32

  Vortex 1200                                            Photometric Chart

 

Ramp Effect

Dimmer

0S (Fade Time)

1S (Fade Time)

0

780

1100

1540

1660

1180

1520

1860

1940

1380

1730

2040

2120

1580

1940

2230

2280

0

0

0

0

0

Standard

Stage

TV

Theatre

Architectural

T

down

ms

T

down

T

down

ms

 

  Vortex 1200                                         Dimmer Curve Chart

3000 2200

1500 1000

800

9500 7200

6000 4500

3300

1200 950

340

150

92

13000 9600

8400 5760

3500

5

20000 11000 7300 5200

3800

0.087 0.175 0.262 0.349 0.437

Summary of Contents for Vortex 1200



















Reviews: