background image

For Your Own Personal Safety, Please Read and Understand This 

Manual Completely Before You Attempt To Install Or Operate 

This Unit!

•   To reduce the risk of electrical shock or fire, do not expose this unit  
   rain or moisture
•   Do not spill water or other liquids into or on to your unit.
•   Do not attempt to operate this unit if the power cord has been 
   frayed or broken. 
•   Do not attempt to remove or break off the ground prong from    
   the electrical cord. This prong is used to reduce the risk of electrical  
   shock and fire in case of an internal short.
•   Disconnect from main power before making any type of connection.
•   Do not remove the cover under any conditions. There are no user  
   serviceable parts inside.
•   Never operate this unit when it’s cover is removed.
•   Always be sure to mount this unit in an area that will allow proper  
   ventilation. Allow about 6” (15cm) between this device and a wall.
•   Do not attempt to operate this unit, if it becomes damaged.
•   This unit is intended for indoor use only, use of this product out-
   doors voids all warranties.
•   Always mount this unit in safe and stable matter.
•   Power-supply cords should be routed so that they are not likely to  
   be walked on or pinched by items placed upon or against them,  
   paying particular attention to cords at plugs, convenience recep- 
   tacles, and the point where they exit from the appliance. 
• Cleaning -The fixture should be cleaned only as recommended by  
   the manufacturer. See page 22 for cleaning details.
•   Heat -This fixture should be situated away from heat sources such 
   as radiators, heat registers, stoves, or other appliances (including 
   amplifiers) that produce heat.
•   The fixture should  be serviced by qualified service personnel when:
    A. Objects have fallen, or liquid has been spilled into the appliance.
    B. The appliance has been exposed to rain or water.
    C.  The  appliance  does  not  appear  to  operate  normally  or  exhibits  a  
     

  

 marked change in performance.

 Nucleus PRO  

 

                        Safety Precautions

American DJ

®

  -  www.americandj.com  - Nucleus PRO Instruction Manual Page 4

American DJ

®

  -  www.americandj.com  - Nucleus PRO Instruction Manual Page 3

•   DMX-512 Protocol Compatible (4, 18, or 22 DMX Channels) 

 

•  X/Y Mirror Control
•  3 Operating Modes - Sound Active, Show Mode, and DMX Control
•  Internal Microphone 
•  Digital Display for Address and Function Setting
•  UC3 Controller (Not Included)

 Nucleus PRO  

 

                                       Features

Caution!

 There are no user serviceable parts inside this unit. Do not 

attempt any repairs yourself, doing so will void your manufactures war-
ranty. In the unlikely event your unit may require service please contact 
American DJ

®

.

American DJ

®

 will not accept any liability for any resulting damages 

caused  by  the  non-observance  of  this  manual  or  any  unauthorized 
modification to this unit.

  Nucleus PRO  

                            Handling Precautions

 Nucleus PRO 

  

                   Warranty Registration

The  Nucleus  PRO  carries  a  3  year  (1095  days)  limited  warranty. 
Please fill out the enclosed warranty card to validate your purchase 
and  warranty.  You  may  also  register  your  product  online  at  www. 
americandj.com. All returned service items whether under warranty or 
not, must be freight pre-paid and accompany a return authorization 
(R.A.) number. If the unit is under warranty you must provide a copy 
of your proof of purchase invoice. Please contact American DJ® cus-
tomer support for a R.A. number.

To  optimize  the  performance  of  this  product,  please  read  these 
operating  instructions  carefully  to  familiarize  yourself  with  the  basic 
operations  of  this  unit.  These  instructions  contain  important  safety 
information  regarding  the  use  and  maintenance  of  this  unit.  Please 
keep this manual with the unit, for future reference.

 Nucleus PRO  

 

                     General Instructions

Summary of Contents for Nucleus PRO













Reviews: