ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 13
ADJ Products, LLC - www.adj.com - Dotz TPar System User Manual Page 12
Universal DMX Control:
This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs. The Dotz TPar System
has 5 DMX channel modes; a 3 Channel Mode, 5 Channel Mode, 9
Channel Mode, 12 Channel Mode, & 18 Channel Mode. See pages
15-21 for the DMX channel modes and traits.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller such as the
Elation® Show Designer™ or the Elation® DMX Operator.™
2. To run your fixture in DMX mode, follow directions on page 8 to
set your DMX address and DMX Channel mode.
3. Plug in the fixture via the XLR connections to any standard DMX
controller.
4. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.
Dotz TPar System Universal DMX Control
Master-Slave Operation:
This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units together
via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector is
the output. The first unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit, designate the unit as a “Master” unit following
the instructions on page 10. Then set your desired operating mode.
3. On the slave units press the MODE button until “Slave Mode” is
displayed.
4. The slave units will now follow the Master unit.
Dotz TPar System Master-Slave Configuration
Dotz TPar System Foot Controller
The Foot Controller has 4 different functions. To control your fix-
ture you must connect the foot controller using the provided cable.
Set the Dotz TPar System to its “Slave” setting. Connect one end
of the cable to the foot controller and the other end to the rear of
the Dotz TPar System bar. To activate the Foot Controller press any
pedal once. To deactivate the Foot Controller press the Blackout and
Program pedals at the same time.
BLACKOUT
-
Pressing this button will blackout the fixture. Press the
pedal for more then 3 seconds to activate Full On.
MODE -
This pedal selects and activates the 3 different operating
modes. Press the pedal for more then 3 seconds to activate Full On.
• Press the MODE pedal and the Red LED lights up, you are Static
Color mode. Use the UP and DOWN pedals to scroll through the 7
different colors.
• Press the MODE pedal and the Green LED lights up, you are in
Sound Active mode. Adjust the sound sensitivity using the knob on
the rear panel of the foot controller.
• Press the MODE pedal and the Yellow LED lights up, you are in the
Built-In Programs mode. Use the UP and DOWN pedals to scroll
through the 14 different programs. Refer to the chart on page 7 for
the programs.
UP -
This pedal works in conjunction with the MODE pedal, it lets
you scroll through the static colors and built-in programs. Press the
UP pedal for more then 3 seconds to activate connected light 1 (right
side of the bar). Press the pedal for more then 3 seconds to deacti-
vate light 1.
DOWN -
This pedal works in conjunction with the MODE pedal, it lets
you scroll through the static colors and built-in programs. Press the
DOWN pedal for more then 3 seconds to activate connected light 2
(left side of the bar). Press the pedal for more then 3 seconds to de-
activate light 2.
