background image

©

American DJ

®

  -  www.americandj.com  - Accu UFO Instruction Manual Page 22

American DJ

®

  -  www.americandj.com  - Accu UFO Instruction Manual Page 21

1. Access the main menu. 
2. Tap the UP button until “

SPEC

” is displayed, press ENTER.

3. Tap the UP button until “

DFSE

” is displayed, press ENTER.

4. The display will show “

ON/OFF

”.  

5. Press the UP button to display “

ON

” to activate this function, 

or “

OFF

” to deactivate this function.

6. Press ENTER to confirm.

7. Press MODE/ESC to return to the main menu.

When you exit this function, the unit will begin to reload 
data.

FEED

  - With this function you can switch the Pan/Tilt error 

correction on and off. This will automatically correct the 

Pan/Tilt if it is somehow moved out of place.

1. Access the main menu.

 

2. Tap the UP button until “

SPEC

” is displayed, press ENTER.

3. Tap the UP button until “

FEED

” is displayed, press ENTER.

4. Press the UP or DOWN buttons to select either “

ON

” to acti-

vate this function, or “

OFF

” to deactivate this function.

5. Press ENTER to confirm.

6. Press MODE/ESC to return to the main menu.

VER

 - Use this function to display the Software version of 

the unit.

1. Access the main menu.
2. Tap the UP button until “

SPEC

” is displayed, press ENTER.

3. Tap the UP button until “

VER

” is displayed, press ENTER.

 Accu UFO   

 

 

                      System Menu

4. The display will show “

V-1.0

”, the display may also show, “

V-

2.0

”, “

V-9.9

” etc.

5. Press MODE/ESC to exit.

ADJU

 - Use this function is used to make sure all motors 

are aligned and to adjust any motors that are not.

1. Access the main menu.
2. Tap the UP button until “

SPEC

” is displayed, press ENTER.

3. Tap the UP button until “

ADJU

” is displayed, press ENTER.

4. Tap the UP button until “

CODE

” is displayed, press ENTER.

5. The display will show “

CXXX

”, were as “XXX” represents the 

calibration password. The calibration password is “C050.” Use 
the UP or DOWN buttons to enter the proper password. 
6. Once the proper password is entered the display will read 

CHXX

”, were as “XX” represents the fixture channel number, in 

the case of the Accu UFO 1~10. 
7. Select the desired channel to be calibrated by pressing the 

UP or DOWN buttons and then ENTER to confirm.

8. The display will then read  “XXXX”, were “XXXX” stands for 
the calibrate values. 
9. Adjust the desired calibration value between  –128 and 127 
by pressing the UP and DOWN. As you scroll up and down 
through the calibration values you will 
notice slight changes in the wheel or motor you are attempting 
to calibrate. 
10. Once you reach your desired calibration press ENTER to 

confirm and lock in your calibration.
11. Once you are completely finished press MODE/ESC to 

return to the main menu.

 Accu UFO   

 

                                System Menu

Summary of Contents for Accu UFO



















Reviews: