background image

American DJ

®

  -  www.americandj.com  - Accu Spot 575 Instruction Manual Page 28

American DJ

®

  -  www.americandj.com  - Accu Spot 575 Instruction Manual Page 27

DLAY

 - With this function you can set a lamp delay time.

1. Access the main menu.
2. Tap the UP button until “

SPEC

” is displayed, press ENTER.

3. Tap the UP button until “

DLAY

” is displayed, press ENTER.

4. The display should show “

D-00

”. Press the UP button in 

order to select your desired delay time. 
5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.

SPOT

  - With this function you can adjust the lamp via 

the control board. The shutter opens and the lamp can be 

adjusted. In this mode, the device will not react to any con-

trol signal.

1. Access the main menu.

 

2. Tap the UP button until “

SPEC

” is displayed, press ENTER.

3. Tap the UP button until “

SPOT

” is displayed, press ENTER.

4. Press the UP or DOWN buttons to select either “

ON

” to acti-

vate this function, or “

OFF

” to deactivate this function.

5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.

DFSE 

- With this function you can restore the factory 

settings of the device. All settings will be set back to the 

default values. Any edited scenes will be lost. When restor-

ing the factory settings the unit must be set to the address 

that the unit was in when you started editing. 

1. Access the main menu. 
2. Tap the UP button until “

SPEC

” is displayed, press ENTER.

 Accu Spot 575 

 

 

                       System Menu

address. First make sure all channels are set to the value of “0”.
1. On your DMX controller set the DMX value of Channel 1 to 
the value “7”.
2. Now set the DMX value of Channel 2 to the value “7” to 
adjust the starting address between 1 and 255. To adjust the 
address between 256 and 511 set Channel 2 to the value “8” .
3. Set the DMX value of Channel 3 to your desired start-
ing address. This will take about 20 seconds before the unit 
accepts the new DMX address. 

EXAMPLE: 

So, if you want the address to be 57, you must first 

set the address that is currently assingned to the unit. The pro-
ceed to set Channel 1s’ value to “7”, Channel 2s’ value to “7”, 
and Channel 3s’ value to “57”. 

2ND EXAMPLE:

 Again, if you want the address to be 420, you 

must first set the address that is currently assingned to the unit.
If you want the set the address to 420, set Channel 1s’ value to 
“7”, Channel 2s’ value to “8”, and Channel 3s to “164”. (256 + 
164 = 420)

DLOF

 - With this function you can switch the lamp on via 

DMX.

1. Access the main menu.
2. Tap the UP button until “

SPEC

” is displayed, press ENTER.

3. Tap the UP button until “

DLOF

” is displayed, press ENTER.

4. Press the UP or DOWN buttons to select either “

ON

” to acti-

vate this function, or “

OFF

” to deactivate this function.

5. Press ENTER to confirm.
6. Press MODE/ESC to return to the main menu.

 Accu Spot 575 

 

 

                       System Menu

Summary of Contents for Accu Spot 575



























Reviews: