manualshive.com logo in svg

Ambirad VISION COMPACT Series, Operation, Maintenance And Servicing Manual

Share
Download
Ambirad VISION COMPACT Series Operation, Maintenance And Servicing Manual Download Page 16

Description Part 

Number

Igniter probes

3149-1

Burner head

3035

Combustion chamber gasket

200553

Support spinning gasket

M101391

Combustion fan

2501

Pactrol control box

2015

Gas valve

2052

Red neon

2180

Amber neon

2175

Wiring harness

900055

Gas valve harness

E300002

HT lead

900064

3 pin mains socket

2135-5

3 pin fan socket

3123-5

Silicone tube

2218

VC20 Natural gas (G20) or Propane (G31) only

Fan orifice plate assembly

200191

Pressure switch (SIT or EAC)

M101355

VC20 Natural gas (G20) only

3.8mm injector

2290

Burner orifice plate 

200520

Burner support spinning

200568-SUB

VC20 Propane (G31) only

2.3mm injector

2281-2

Burner orifice plate 

3161-2MF

Burner support spinning

200521-SUB

VC12 Natural Gas (G20) or Propane (G31) only

Fan orifice plate assembly

FSER12USA30

Pressure switch (SIT or EAC)

2190

VC12 Natural Gas (G20) only

3.0mm injector

4578

Burner orifice plate 

3161-2MF

Burner support spinning

200521-SUB

VC12 Propane (G31) only

1.9mm injector

4579

Burner orifice plate 

3161-2MF

Burner support spinning

200521-SUB

17  Spare parts

14

Summary of Contents for VISION COMPACT Series




















Reviews:

No comments

Brands by name

Popular brands

Load more brands