background image

 

Version 1.1  

 

©Copyright 2015, Ambient LLC. All Rights Reserved. 

 

 

 

Page 6 

4 Display Console Set Up 

Move the remote sensor(s) about 5 to 10’ away from the display console (if the sensor is too close, it 
may not be received by the display console).   
 
If  you  have  more  than  one  remote  sensor,  make  sure  they  are  all  powered  up  and  transmitting  on 
different channels. Remove the battery door on the back of the display, as shown i

Figure 5

. 

 

 

 

Figure 5 

 
Fold out the desk stand, remove the battery cover, and insert three AAA (alkaline or lithium, avoid 
rechargeable unless fully charged and high quality) batteries in the back of the display console.    All 
of the LCD segments will light up for a few seconds (to verify all segments are operating properly). 
 

1.

 

Replace  the  battery  door,  and  place  the  console  in  the  upright  position  with  the  desk  stand 
folded out.   
 
The  console  will  instantly  display  time  and  indoor  temperature  as  designated.  The  remote 
temperature will update on the display within a few minutes on the appropriate channel.   
 
While in the search mode, the remote search icon 

  will be constantly displayed. 

 
If  you  have  more  than  once  remote  sensor  (up  to  eight remotes  are  supported),  the display 
will automatically toggle between sensors until all sensors have reported in. 
 
Do  not  touch  any  buttons  until  the  remote  sensor  has  reported  in,  or  the  radio  search  icon 

Summary of Contents for WS-16















Reviews: