Amana GCIA045A30, Service Instructions Manual

Page: 27 / 106

BLOWER PERFORMANCE SPECIFICATIONS
27
Rev. 2
1. Units are shipped without filter(s). CFM in chart is without filter(s).
2. All furnaces shipped as high speed for cooling. Installer should adjust blower speeds as needed.
3. INSTALLATION IS TO BE ADJUSTED TO OBTAIN TEMPERATURE RISE WITHIN THE RANGE SPECIFIED ON THE
RATING PLATE.
4. The chart is for information only. For satisfactory operation, external static pressure not to exceed value shown on
rating plate. The shaded area indicates ranges in excess of maximum external static pressure allowed when heating.
5. The above chart is for U.S. furnaces installed at 0-2000 feet. At higher altitudes, a properly derated unit will have
approximately the same temperature rise at a particular CFM, while the ESP at that CFM will be lower.
SINGLE STAGE
MODEL TONS AC
External Static Pressure, Inches Water Column
(Htg. Speed @ 0.5" 0.1 0.2 0.3 0.4 0.5 0.6
As Shipped) ESP CFM Rise CFM Rise CFM Rise CFM Rise CFM Rise CFM Rise
HIGH 3.0 1460 - 1400 - 1345 - 1280 - 1200 - 1110 -
GUI_045_30 MED-HI 2.5 1200 - 1150 - 1100 - 1050 - 980 35 900 38
(Low) MED-LO 2.0 935 36 910 37 885 39 845 40 790 43 710 48
LOW 1.5 700 49 685 50 665 51 635 54 575 59 425 -
HIGH 3.0 1555 - 1505 - 1440 35 1365 37 1290 39 1180 43
GUI_070_30 MED-HI 3.0 1325 38 1305 39 1250 41 1200 42 1140 44 1060 48
(Med-Lo) MED-LO 2.5 1090 47 1080 47 1055 48 1020 50 970 52 905 56
LOW 2.0 760 - 750 - 750 - 735 - 700 - 645 -
HIGH 3.5 1695 - 1625 - 1580 - 1520 - 1450 35 1365 37
GUI_070_40
MED-HI 3.0 1485 - 1450 35 1400 36 1350 38 1295 39 1235 41
(Low) MED-LO 3.0 1235 41 1200 42 1180 43 1140 44 1115 45 1050 48
LOW 2.5 1095 46 1070 47 1050 48 1025 49 975 52 950 53
HIGH 3.5 1630 42 1560 44 1550 44 1465 47 1380 49 1275 53
GUI_090_30 MED-HI 3.0 1360 50 1325 51 1290 53 1215 56 1155 59 1070 64
(High) MED-LO 2.0 920 - 920 - 900 - 890 - 850 - 800 -
LOW 1.5 770 - 750 - 740 - 730 - 690 - 660 -
HIGH 5.0 2250 - 2185 - 2120 - 2030 - 1975 - 1885 -
GUI_090_50
MED-HI 4.0 1775 - 1750 - 1735 - 1690 40 1650 41 1600 43
(Med-Lo) MED-LO 3.5 1320 52 1315 52 1315 52 1315 52 1280 53 1240 55
LOW 3.0 1180 58 1180 58 1175 58 1170 58 1140 60 1120 61
HIGH 4.0 1835 46 1780 48 1730 49 1660 51 1590 53 1530 55
GUI_115_40
MED-HI 3.5 1630 52 1595 53 1540 55 1490 57 1440 59 1375 62
(High) MED-LO 3.0 1320 64 1305 65 1290 66 1260 67 1200 - 1180 -
LOW 2.5 1140 - 1145 - 1120 - 1100 - 1065 - 1030 -
HIGH 5.0 2330 36 2245 38 2165 39 2065 41 1985 43 1885 45
GUI_115_50 MED-HI 5.0 2120 40 2070 41 2020 42 1940 44 1850 46 1775 48
(Med-Hi) MED-LO 4.0 1875 45 1840 46 1800 47 1735 49 1685 50 1600 53
LOW 3.0 1290 - 1275 - 1250 - 1235 - 1210 - 1170 -
HIGH 5.0 2455 - 2390 - 2290 - 2200 46 2050 49 1935 52
GUI_140_50
MED-HI 5.0 2050 49 2025 50 1965 52 1890 54 1810 56 1715 59
(High) MED-LO 4.0 1715 59 1700 60 1660 61 1615 63 1555 65 1470 69
LOW 3.5 1450 70 1435 71 1415 72 1380 73 1340 - 1280 -
CFM & Temperature Rise vs. External Static Pressue
MOTOR
SPEED