A–7
RS5320010 Rev. 1
Programming Instructions
Multiple Heating Stages
Oven can be programmed to perform 4 independent
heating cycles without interruption.
1. Open oven door.
• Display shows “b” or “d” and “READY”.
• Fan and light operate.
• If door is closed or
RESET pad is pressed before
finishing programming sequence, oven exits
programming mode.
2. Press pad
1 for approximately 5 seconds.
• After 5 seconds, signal sounds. Display shows
“Pb” or “Pd” indicating “b” or “d” menu.
3. Press
MENU b/d pad to select preprogrammed menu
if necessary.
4. Press desired number pad.
• Display shows heating time, “COOK LEVEL” and
power level if other than 100 percent power.
5. Press number pads to enter desired cooking time.
• For example, to heat for 2 minutes 30 seconds,
press
2, 3, and 0 pads.
6. Press
POWER LEVEL pad if power level other than
100 percent is required.
• Display shows “COOK LEVEL” and current power
level if other than 100 percent power.
7. Press number pad to enter desired power level.
• For example, pressing
2 pad is 20 percent power.
8. Press
TIME ENTRY pad.
• Display briefly shows "bP1
(1-9,0)
" or "dP1
(1-9,0)
"
indicating menu, programming, stage, and pad.
Then cook time and power level for stage show in
display.
• Repeat steps 5-8 to create additional stages.
9. Press
START pad to save new heating time and
power level in oven memory.
10. Press
RESET pad or close oven door to exit
programming mode.
Deactivating Preprogrammed Pad
1. Open oven door.
• Display shows “b” or “d” and “READY”.
• Fan and light operate.
• If door is closed or
RESET pad is pressed before
finishing programming sequence, oven exits
programming mode.
2. Press and hold pad
1 for approximately 5 seconds.
• After 5 seconds, signal sounds. Display shows
“Pb” or “Pd” indicating “b” or “d” menu.
3. Press desired number pad.
• Display shows heating time, “COOK LEVEL” and
power level if other than 100 percent power.
4. Press
MENU b/d pad.
• “
dddd” and pad number show in display.
5. Press
START pad to save in oven memory.
• To reactivate pad, repeat steps.
6. Press
RESET pad or close oven door to exit
programming mode.
Reactivating Preprogrammed Pad
1. Open oven door.
• Display shows “b” or “d” and “READY”.
• Fan and light operate.
• If door is closed or
RESET pad is pressed before
finishing programming sequence, oven exits
programming mode.
2. Press and hold pad
1 for approximately 5 seconds.
• After 5 seconds, signal sounds. Display shows
“Pb” or “Pd” indicating “b” or “d” menu.
3. Press desired number pad.
• Display shows heating time, “COOK LEVEL” and
power level if other than 100 percent power.
4. Press
MENU b/d pad.
• Display shows “0000” and “READY”.
5. Program pad according to “Preprogrammed Number
Pads” section step 5-8.
6. Press
START pad to save in oven memory.
• To reactivate pad, repeat steps.
7. Press
RESET pad or close oven door to exit
programming mode.
Deactivating Control Panel
1. Open oven door, and close oven door.
• Display shows “b” or “d” and “READY”.
• Fan and light operate.
• If pad is not pressed in 30 seconds, open and
close oven door again.
2. Press
TIME ENTRY pad.
• Display shows “0000” and “READY”.
3. Press
1,3,5, and 7 pad in sequence.
4. Press
TIME ENTRY pad.
• “LOC” shows in display.
• All pads except
TIME ENTRY are disabled.
• To reactivate control repeat steps 1-4.
