RS5320010 Rev. 1
A–6
Programming Instructions
Reviewing Preprogrammed Pads
1. Open oven door.
• Display shows “b” or “d” and “READY”.
• Fan and light operate.
• If door is closed or
RESET pad is pressed before
finishing programming sequence, oven exits
programming mode.
2. Press and hold
TIME ENTRY pad for approximately 5
seconds.
• After 5 seconds, signal sounds. Display shows
“Pb” or “Pd” indicating “b” or “d” menu.
3. Press
MENU b/d pad to select preprogrammed menu
if necessary.
4. Press desired number pad.
• Display shows heating time, “COOK LEVEL” and
power level if other than 100 percent power.
5. Press
TIME ENTRY pad to review heating stages for
pad.
• “P(b or d)” and stage show briefly, then heating
time, “COOK LEVEL” and power level if other than
100 percent power show in display.
6. Press
START pad after reviewing preprogrammed pad.
• Display shows “Pb” or “Pd” indicating “b” or “d”
menu.
• Repeat steps 3-6 to review another preprogrammed
pad.
7. Press
RESET pad or close oven door to exit
programming mode.
Manual Time Entry
1. Open oven door, place food in oven, and close oven
door.
• Display shows “b” or “d” and “READY”.
• Fan and light operate.
• If pad is not pressed in 30 seconds, open and
close oven door again.
2. Press
TIME ENTRY pad.
• Display shows “0000” and “READY”.
3. Press number pads to enter desired cooking time.
• For example, to heat for 2 minutes 30 seconds,
press
2, 3, and 0 pads.
4. Press
POWER LEVEL pad if power level other than
100 percent is required.
• Display shows “COOK LEVEL” and current power
level if other than 100 percent power.
5. Press number pad to enter desired power level.
• For example, pressing
2 pad is 20 percent power.
6. Press
START pad.
• Oven operates and time counts down.
• Display shows heating time, “POWER”, “COOK
LEVEL”.
• Display shows “POWER” only when microwave
energy is present.
• If power level other than 100 percent power was
programmed, display shows “COOK LEVEL” and
power level. Display counts down cooking time.
7. Oven stops heating and oven signal sounds when
heating timing elapses.
Preprogrammed Number Pads
1. Open oven door.
• Display shows “b” or “d” and “READY”.
• Fan and light operate.
• If door is closed or
RESET pad is pressed before
finishing programming sequence, oven exits
programming mode.
2. Press and hold pad
1 for approximately 5 seconds.
• After 5 seconds, signal sounds. Display shows
“Pb” or “Pd” indicating “b” or “d” menu.
3. Press
MENU b/d pad to select preprogrammed menu
if necessary.
4. Press desired number pad.
• Display shows heating time, “COOK LEVEL” and
power level if other than 100 percent power.
5. Press number pads to enter desired cooking time.
• For example, to heat for 2 minutes 30 seconds,
press
2, 3, and 0 pads.
6. Press
POWER LEVEL pad if power level other than
100 percent is required.
• Display shows “COOK LEVEL” and current power
level if other than 100 percent power.
7. Press number pad to enter desired power level.
• For example, pressing
2 pad is 20 percent power.
8. Press
START pad to save new heating time and
power level in oven memory.
• Display shows “Pb” or “Pd” indicating “b” or “d”
menu.
• Repeat step 3-8 to program additional pads.
9. Press
RESET pad or close oven door to exit
programming mode.
