AlterG Anti-Gravity Treadmill Via 400 User Manual Download Page 50

Page: 50 / 56

D-000348 Rev. A

Appendix B: Accessories and Options

AlterG Short

s Available in the following standard sizes: XS, S, M, L, XL, XXL, XXXL,

4XL. Performance 2.0 shorts available in the following sizes: XS, S, M, L, XL, XXL,
XXXL. Custom sizes are available as options as well.

Replacement Safety Magnet

– The AlterG Treadmill will not operate without the safety

magnet

Zip Care Zipper Lubricant –

Prolong the life of your fabric enclosure and zipper.

Strataglass Cleaner

– Keep the viewing area clear with this special cleaner.

SlipCoat

– One-ounce packets of lubricant made specifically for the Landice Treadmill.

Used as recommended will help prevent premature failure due to friction and excessive
wear.

Contact your AlterG Sales representative for pricing and ordering.

Summary of Contents for Anti-Gravity Treadmill Via 400

























































Search results

Summary of Contents for Anti-Gravity Treadmill Via 400

Reviews:

Related manuals for Anti-Gravity Treadmill Via 400

Brands by name

Popular brands

AlterG Anti-Gravity Treadmill Via 400, User Manual

Search results

Summary of Contents for Anti-Gravity Treadmill Via 400

Reviews:

Related manuals for Anti-Gravity Treadmill Via 400

Brands by name

Popular brands