AlterG Anti-Gravity Treadmill Via 400 User Manual Download Page 2

Page: 2 / 56

D-000348 Rev. A

This manual covers operation procedures for the following AlterG products:

AlterG Anti-Gravity Treadmill

Via400, 400M, and 400X

NOTE: The following symbol is used throughout this manual to call attention to Warnings,

Cautions or operational procedures that may directly affect the safe operation of the AlterG

Anti-Gravity Treadmill. Read and understand these instructions and statements before

operating the AlterG Anti-Gravity Treadmill.

Note: The AlterG Anti-Gravity Treadmill has been tested to IEC medical standards for electrical

safety.

IEC 60601-1:2005 + A1 2012

IP20

AlterG and Anti-Gravity Treadmill are registered trademarks in the US by AlterG, Inc.

European Authorized Representative:

Obelis s.a.

Tel: +(32) 2.732.59.54

Bd. Général Wahis 53

Fax: +(32) 2.732.60.03

1030 Brussels, Belgium

Email: [email protected]

Warning, Cautionary statement or operational procedure
that may directly affect the safe operation of the

treadmill.

Summary of Contents for Anti-Gravity Treadmill Via 400

























































Search results

Summary of Contents for Anti-Gravity Treadmill Via 400

Reviews:

Related manuals for Anti-Gravity Treadmill Via 400

Brands by name

Popular brands

AlterG Anti-Gravity Treadmill Via 400, User Manual

Search results

Summary of Contents for Anti-Gravity Treadmill Via 400

Reviews:

Related manuals for Anti-Gravity Treadmill Via 400

Brands by name

Popular brands