Alpha Technologies TRI POWER X33 MOD HP 10 kVA Operating And Maintenance Manual Download Page 71

Page: 71 / 80

Tri Power X33 Mod HP Manual | Rev 1.20 | © Alpha Technologies GmbH 2013

Operating

nd Main

tena

nce

Manua

Tri Power X33 Mod HP

ALARMS

Message

Meaning

INVERTER FAILURE

Failure occurred in the Inverter circuit.

BOOSTER FAILURE

Failure occurred in the Booster circuit.

BATTERY CHARGER FAILURE

Failure occurred in the Battery Charger circuit.

OVERHEATING

Overheating. Check the UPS ventilation system.

OVERLOAD

Overload. Check the load level connected to the UPS.

HVBUS RUNAWAY

Anomalous high voltage on the DC BUS.

EXC. IN OUT DC LEVEL

Excessive DC voltage in output.

EXCESS.BATTERY V

Battery voltage too high.

MODULE COMMUNICATION
FAILED

Failure of the communication system with the Power Modules.

LOAD NOT PROTECTED

Load not protected by the UPS.

Summary of Contents for TRI POWER X33 MOD HP 10 kVA

















































































Search results

Summary of Contents for TRI POWER X33 MOD HP 10 kVA

Reviews:

Related manuals for TRI POWER X33 MOD HP 10 kVA

Brands by name

Popular brands

Alpha Technologies TRI POWER X33 MOD HP 10 kVA, Operating And Maintenance Manual

Search results

Summary of Contents for TRI POWER X33 MOD HP 10 kVA

Reviews:

Related manuals for TRI POWER X33 MOD HP 10 kVA

Brands by name

Popular brands