Alpha Technologies TRI POWER X33 MOD HP 10 kVA Operating And Maintenance Manual Download Page 69

Page: 69 / 80

Tri Power X33 Mod HP Manual | Rev 1.20 | © Alpha Technologies GmbH 2013

Operating

nd Main

tena

nce

Manua

Tri Power X33 Mod HP

IMPORTANT EVENTS

Message

Meaning

INVERTER FAILURE

Failure occurred in the Inverter circuit.

BOOSTER FAILURE

Failure occurred in the Booster circuit.

BATTERY CHARGER FAILURE

Failure occurred in the Battery Charger circuit.

OVERHEATING

Overheating. Check the UPS ventilation system.

OVERLOAD

Overload. Check the load level connected to the UPS.

EXCESSIVE VOLTAGE ON THE
H.V. BUS

Anomalous high voltage on the DC BUS.

EXCESSIVE DC LEVEL IN
OUTPUT

The DC (Direct Current) level in output is excessive.

EXCESSIVE BATTERY VOLTAGE

Battery voltage too high.

POWER MODULE
COMMUNICATION FAILURE

Failure of the communication system with the Power Modules.

EMERGENCY

Emergency.

LOAD NOT POWERED

Power to the loads has been interrupted.

ABNORMAL SHUTTING DOWN

UPS shut down abnormally

SHUTTING DOWN DUE TO AN
OVERLOAD

UPS shut down due to an overload.

SHUTTING DOWN DUE TO AN
EMERGENCY POWER OFF

UPS shut down due to an Emergency Power Off.

BATTERIE KO

Battery failure.

Summary of Contents for TRI POWER X33 MOD HP 10 kVA

















































































Search results

Summary of Contents for TRI POWER X33 MOD HP 10 kVA

Reviews:

Related manuals for TRI POWER X33 MOD HP 10 kVA

Brands by name

Popular brands

Alpha Technologies TRI POWER X33 MOD HP 10 kVA, Operating And Maintenance Manual

Search results

Summary of Contents for TRI POWER X33 MOD HP 10 kVA

Reviews:

Related manuals for TRI POWER X33 MOD HP 10 kVA

Brands by name

Popular brands