Alpha ESS SMILE-S5-HV Installation Manual Download Page 67

Page: 67 / 75

___________________________________________________________________

Alpha ESS Co., Ltd.

Page 67 of 75

Your Smart Energy

10.2.2

Battery Protection Description

LED Indictor

Protection

Code

LED Display

Description

Troubleshooting

Yellow LEDs
flash once
every 1S.

Temperature
difference

Wait for automated recovery.
In case the problem is not
recovery for a long time, call for
service.

High temperature

Stop discharging and charging
until this code is eliminated and
wait for the temperature to drop.

Low-temperature
discharge

Stop discharging until this code is
eliminated and wait for the
temperature to rise.

Over-current charge

Wait for automated recovery.
If the problem is not
recovery for a long time, call for
service.

Over-current
discharge

Cell overvoltage

Cell under voltage

Stop discharging and call service
immediately.

Low-temperature
charge

Stop discharging until this code is
eliminated and wait for the
temperature to rise.

Summary of Contents for SMILE-S5-HV












































































Search results

Summary of Contents for SMILE-S5-HV

Reviews:

Related manuals for SMILE-S5-HV

Brands by name

Popular brands

Alpha ESS SMILE-S5-HV, Installation Manual

Search results

Summary of Contents for SMILE-S5-HV

Reviews:

Related manuals for SMILE-S5-HV

Brands by name

Popular brands