Alpha ESS SMILE-S5-HV Installation Manual Download Page 41

Page: 41 / 75

___________________________________________________________________

Alpha ESS Co., Ltd.

Page 41 of 75

Your Smart Energy

7.4.4

Meter Connection

The system supports the following two different metering schemes in order to record
the feed-in energy and consumption from grid:

⚫

DTSU666-3*230V 5A: Three/single-phase meter (without CT)

⚫

DTSU666-100/40mA: Three/single-phase meter (with 3 or 6 CTs)

Meter wiring introduction

NOTICE

∙

If the extra PV inverter are not used, the system is suitable for DC mode.

∙

If you use the extra PV inverter, the system is suitable for AC or Hybrid mode.

1. DTSU666-3*230V 5A: Three-phase meter (without CT) connection

Wiring at single-phase home

Wiring at three-phase home

2. DTSU666-100/40mA: Three-phase meter (with 3 or 6 CTs) connection

Wiring at single-phase home

Summary of Contents for SMILE-S5-HV












































































Search results

Summary of Contents for SMILE-S5-HV

Reviews:

Related manuals for SMILE-S5-HV

Brands by name

Popular brands

Alpha ESS SMILE-S5-HV, Installation Manual

Search results

Summary of Contents for SMILE-S5-HV

Reviews:

Related manuals for SMILE-S5-HV

Brands by name

Popular brands