manualshive.com logo in svg

ALP K2 DM-4000, Instructions Manual, Page: 22 / 36

Share
Download
ALP K2 DM-4000 Instructions Manual Download Page 22

- 22 -

Operation with built-in rechargeable battery

Charging the rechargeable battery

If the AC adaptor is connected correctly, the adaptor mark of 
the display section switches on.
The battery is charged regardless of whether the power of 
the main unit is on or off.
While the battery is being charged, the battery mark flashes.
When the battery is charged, the mark switches to the 
remaining indication. Charging takes about four hours.

Remaining charge of the rechargeable battery

If the remaining charge of the battery is low, the battery mark on the display flashes.
This indicates the remaining battery charge for a few measurements.

If the battery mark changes from flashing to remaining indication, measurement is not 
possible. Charge the battery.

About the rechargeable battery

 

◆

The rechargeable battery may not be charged sufficiently the first time you use it or if you do not use it 
for a long time.
This is due to the characteristics of rechargeable batteries. This is resolved by using the rechargeable 
battery (with electrical charging and discharging) several times.

 

◆

While it depends on the operating environment and conditions, the life of the rechargeable battery is 
about two years.
To ensure extended use of the rechargeable battery, we recommend charging the rechargeable battery 
after it has completely run out.
If the battery mark flashes frequently or charging is necessary frequently, replace the rechargeable 
battery.

When you purchase consumables, contact a dealer.

Model: GP170AAH

BATTERY PLUG

RECHARGEABLE NICKEL METAL 

HYBRID (NiMH) BATTERY

Phillips head
screwdriver

Rear of

main unit

BATTERY PLUG

BATTERY

CONNECTOR

Tighten

Loosen

Flashing: charging

On: charged

： 

Adaptor mark

： 

Battery mark

If the built-in rechargeable battery has been charged, this product can be used without the AC adapter.
Charge for about four hours before use.

Remaining

Flashing

Flashing

Summary of Contents for DM-4000





































Reviews:

No comments