manualshive.com logo in svg

Allnet ALL6800, User Manual

Share
Download
Allnet ALL6800 User Manual Download Page 15

 

 
 

15 

Checking System Status 

After making connections on the ALL6800 and powering up, check whether the 
system status is normal or has trouble by observing indicators on the front panel 

and hard disk trays. 
 

System Status Normal 

The system status is normal if: 

 

1.

 

The WAN and LAN LEDs glow green 

(assuming both are connected). 

 

2.

 

The Power LED on the Front Panel glows 
blue. 

 

3.

 

The HDD Power LED on each HDD tray 
glows blue (assuming all disks are 

installed). 

 

4.

 

The default IP address of the WAN port is 
192.168.1.100 displayed on LCD. 

 
 

 

 

System Trouble 

The system has trouble if: 
 

1.

 

System Busy LED glows red. 

 

If the system has trouble, please refer to 

Chapter 8: Troubleshooting

. 

 

 
 

 
 
 

 
 

 
 

 
 

 
 
 

WARNING 

There are no user serviceable parts inside the ALL6800. Please contact 

your distributor for service. 

Summary of Contents for ALL6800























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands