Allnet ALL6800 User Manual Download

Page: 38 / 118

NFS Share

To allow NFS access to the share folder, enable the NFS Service, and then set up

hosts with access rights by clicking Add.

NFS Share

Item Description
Hostname

Enter the name or IP address of the host

Privilege

Host has either read only or writeable access to the folder.

Guest System Support There are two selections available:

•

Unix / Linux System

•

AIX (Allow source port > 1024)

Choose the one which best fits your needs.

IO Mapping

There are three selections available:

•

Guest system root account will have full access to this

share (root:root).

•

Guest system root account will be mapped to
anonymous user (nobody:nogroup) on NAS.

•

All user on guest system will be mapped to anonymous

user (nobody:nogroup) on NAS.

Choose the one which best fits your needs.

Apply

Click to save your changes.

Back

Click to abandon changes.

Snap (Snapshot configuration)

If added folder has located in the RAID volume with “ZFS” file system, then the
folder management screen with “Snap” button will be configurable.

Clicking on “Snap” then screen appears as following.

Summary of Contents for ALL6800























































































































Search results

Summary of Contents for ALL6800

Reviews:

Related manuals for ALL6800

Brands by name

Popular brands

Allnet ALL6800, User Manual

Search results

Summary of Contents for ALL6800

Reviews:

Related manuals for ALL6800

Brands by name

Popular brands