Not for
Reproduction
5-8
MAINTAINING THE LIGHT TOWER TRAILER
MAINTAINING THE LIGHT TOWER AND
LAMPS
CHANGING LAMPS
WARNING
BURN HAZARD
The light bulbs and fixtures become extremely hot
during use. Allow the bulbs and fixtures to
sufficiently cool down before changing bulbs or
severe burns may occur.
To change the lamps:
1
Turn off the lights and shut off the engine. Allow the
bulbs and fixtures to cool.
2
Lower the light tower to the full down position.
3
Loosen the lens channel screws to allow the removal
of the lens channel.
4
Remove the silicone gasket and lens.
5
Remove the support clip screws and support clip.
6
Carefully remove the old lamp and install the correct
replacement.
7
Clean the reflector and lens.
8
Install the support clip and screws.
9
Install the silicone gasket and lens (replace if
damaged).
10
Install the lens channel and screws.
11
Test the new lamp to make sure that it operates
properly.
MAINTAINING THE TRAILER
Proper maintenance and care of your trailer is a must for
safe and reliable operation. Follow these maintenance
and care guidelines in addition to those scheduled by
your shop equipment maintenance schedule.
MAINTAINING THE TRAILER FRAME
To maintain the trailer frame:
1
Check the coupler operation. Also check for corrosion
or damage. Repair or replace as needed.
2
Inspect the lifting bar for corrosion or damage and
repair or replace as needed.
3
Inspect the trailer frame and body panels for rust,
nicks, and chips. Use the proper touch-up paint to
touch up nicks or scratches. Contact your dealer for
additional information.
4
Inspect the axle, springs, and undercarriage for wear
and damage. Repair or replace as needed.
5
Inspect the outrigger bars, front and rear stabilizer
jacks, and locking mechanisms for proper operation,
wear, and damage. Repair or replace as needed.
6
Inspect the safety chains for wear and corrosion
damage. Repair or replace as needed.
Lens channel
Silicone gasket
Lens
Reflector
Support clip
screws (2)
Support
clip
Lamp
Lens channel
screws and
nuts (2 each)
Summary of Contents for Maxi-Lit II
