allen MP245 Operations & Parts Manual Download Page 36

Page: 36 / 106

SECTION 2

OPERATIONS

067975

Page 36

Before operation each day ensure the following:

• All guards, side screens and panels are in place.

• All safety and information signs are in place and legible.

• Engine and hydraulic oil levels are correct.

• Check battery level

• Check for hydraulic leaks.

• Check all operating controls for proper operation and adjustment.

• Check speed control operation before and after starting engine for proper operation.

• Gearbox oil level. Add oil as required.

• The steering, left and right.

Note:

If there is any indication that faulty equipment exists, shutdown safely, inform the proper authority and

DO NOT

erate the riding trowel until the problem has been fixed.

• Remove loose objects that could interfere with operation.

Pre Operating Instructions

WARNING!

Oil MUST be present and flowing through the Auxiliary

Pump when running the machine. The warranty will be

voided if no oil is present. When replacing the pump, it

MUST be primed before starting machine.

Summary of Contents for MP245











































































































Search results

Summary of Contents for MP245

Reviews:

Related manuals for MP245

Brands by name

Popular brands

allen MP245, Operations & Parts Manual

Search results

Summary of Contents for MP245

Reviews:

Related manuals for MP245

Brands by name

Popular brands