Allen Engineering Corporation RAZORBACK 12HD Operation Manual Download Page 11

OPERATIONS 

SECTION 1 

• TECHNICAL DATA • 

SPECIFICATIONS ON AIR POWERED SCREED: 

MODEL 

TRUSS BLADES 

10’ 

lbs/kg 

7 1/2’ 

lbs/kg 

5’ 

lbs/kg 

 2 1/2’ 

lbs/kg 

2’ 

lbs/kg 

MAXIMUM 

WIDTHS 

12SX 

12 GA. GALV. STEEL 

140/64 

104/47 

70/32 

36/16 

28/13 

55’ 

12HD 

10 GA. GALV. STEEL 

186/84 

138/63 

93/42 

47/21 

37/17 

65’ 

12SHD 

10 GA. STAINLESS 

186/84 

138/63 

93/42 

47/21 

37/17 

75’ 

Top Pipe - Coupling System - Fine Thread Adjustment 1 5/16-16tpi with Full Flow 1” Non-
Restricting Air System with Dual Locking Jam Nuts. 

Vibration Proof Welds with Exclusive Vibration-Dampening System. 

Bolt-On Blades with Quick Connecting Splice Plates Front and Back at each Truss Section using 
1/2-13 Nuts and Bolts Throughout. 

Balanced Design Truss Height to Overall Base Width Provides Equilateral Triangle Strength for 
Obtaining Precise Grade Control and Structure Integrity. 

Top Pipe Coupling System Provides for Crowned or Invert Slab Section without loosening Bottom 
Splice Blade Bolts.  Special Crowns or Inverts are obtainable with Ball Joint Top Pipe Coupler or 
Crown Invert Bracket.  Crowns greater than 1/8”/ft are considered special. 

NOTE: Select Screed Width to Allow Minimum Overhangs Past Forms; 6” Overhangs are Ideal, 

S1-8 

MODEL 

1.  SINGLE 

VIBRATORS 

2. DUAL 

VIBRATORS 

12SX 

9

 

 

12HD 

 

9

 

12SHD 

 

9

 

VIBRATORS PER SECTION 

            7-1/2'                       5'                             2'  

1.  SINGLE VIBRATORS 30" centers alternating front to back. 
2.  DUAL VIBRATORS 30" centers front and back. 
 

VIBRATORS - Naval Bronze Piston Pneumatic Vibrator.  Rebuildable, Rust-Resistant, One 
Moving Part, Fatigue Proof Air Fitting.  Weight 2.42#.  Piston is 1" Diameter with Unbalanced 
travel.  Air Consumption 4.0 CFM at 60 PSI.  Vibrations Per Minute, 9500 at 60 PSI. 

Exclusive 3 Bolt Attaching Bracket using High Strength Fine Thread Double Nut Vibrator Bolt with 
2 each 1/2" Bracket Bolts. 

Vibratory Supply Air Supply - 200 PSI with Push Lock Fittings. 

Full Flow 1" Air Flow System - Includes Air Connecting Hose to Screed, Off/On Valve Also used 
as Volume Flow Valve, Air Gauge, In-line 1" Mist Lubricator Provides Adjustable Lubrication.  
Top Dome Sight Drip Glass, Fill Cap, 1 Quart Capacity Steel Body with Sight Glass for 
Lubrication Oil. 

Lubrication Mist Lube - NR88 or Allen Air Lube; Aft Dextron II is Allowable for Intermittent Use. 

Summary of Contents for RAZORBACK 12HD
































Reviews: