background image

82

Rockwell Automation Publication 2097-UM002D-EN-P - April 2017

Chapter 5

Configure and Start up the Kinetix 350 Drive System

By accessing these four parameters, the full IP address on the drive can be 
obtained.

If parameters IP_1, IP_2, IP_3, and IP_4 all contain ‘----‘ rather than a 
numerical values it means that the drive has DHCP enabled and the DHCP 
server has yet to assign the drive its dynamic IP address. As soon as server 
assigns an IP address the drive displays the address in the IP_1, IP_2, IP_3, and 
IP_4 parameters. See Configure the IP Address Automatically (Dynamic 
Address) o
n 

page 83

.

Configure the IP Address Manually (Static Address)

When connecting directly from the Kinetix 350 drive to the personal 
computer without a server or when connecting to a private network, where all 
devices have static IP addresses, assign the IP address of the Kinetix 350 drive 
manually.

To assign the address manually, disable the DHCP mode. Do following the 
steps by using the drive keypad.

1.

Press . 

2.

Use

to access parameter DHCP.

3.

Check that this parameter is set to a value of 0. 

4.

If the DHCP parameter is set to 1, then use

and

to set to 0.

5.

Cycle power to the drive.

The change takes effect. 

When DHCP is disabled and the power is cycled to the drive, it reverts to its 
previous static IP address.

If you are connecting multiple drives to the personal computer, create unique 
IP address for each drive. Do it by using the keypad on each drive to change the 
IP_4 parameter. IP_4 is the only octet that can be changed via the keypad. 
IP_1, IP2, and IP_3 are read-only accessed this way. The dive power must be 
cycled for any changes to take effect.

Summary of Contents for Kinetix 350



































































































































































Reviews: