Allen-Bradley Bulletin 2364F Troubleshooting Manual Download Page 34 | Manualshive

Page: 34 / 64

background image

Publication 2364F-5.05 - March 1999

4-6

Testing Components

Replacing the Battery for the Battery-Backed Memory on the Main
Control Board

Replacing the battery on the main control board (U11) will erase all
modified parameters. Record parameters before replacing the battery.

1. Push the disconnect lever to off and wait for all voltage to discharge

from the unit. Do not continue until all voltage has dissipated from the
DC bus.

2. Verify that there is no voltage across the DC bus (see Figure 4.12 and

Figure 4.13 for check points).

3. Verify that there is no voltage across the terminals and subcomponents

of the main control board.

4. Put on an electrostatic discharge (ESD) protective strap and connect the

strap to one of the door latches.

5. Grasp the battery, from the top and bottom, and gently pull the battery

off of U11 as shown in Figure 4.3 (note the orientation of the battery).

6. Gently press the new battery into place (the battery can only be installed

in one orientation).

7. Properly dispose of the lithium battery according to your local

ordinances and company procedures.

Figure 4.3
Replacing the Battery for the Battery-Backed Memory

Battery-Backed
Memory (U11)

Lithium Battery and Crystal Package (2.8V, 49mAh)

See publication 1756-5.68 for guidelines
concerning lithium battery disposal.

«
...
32
33
34
35
36
...
»

Summary of Contents for Bulletin 2364F

































































Reviews:

No comments

Related manuals for Bulletin 2364F

Brand: YSI Pages: 70

Brand: jcb Pages: 41

Brand: NEILPRYDE Pages: 53

Brand: JAC Pages: 103

Brand: 3Disc Pages: 12

Brand: Ace Pages: 17

Brand: ACE INSTRUMENTS Pages: 33

Brand: ACE INSTRUMENTS Pages: 2

Brand: ACE INSTRUMENTS Pages: 2

Brand: TapFlo Pages: 35

Brand: DANA Pages: 8

Brand: 2E Pages: 6

Coronis 5MP Mammo

Brand: Barco Pages: 4

Brand: Barco Pages: 167

Color Coronis 2MP

Brand: Barco Pages: 156

Color Coronis 2MP

Brand: Barco Pages: 12

Brand: Barco Pages: 39

Brand: Barco Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands