Allen-Bradley Bulletin 2364F Troubleshooting Manual Download Page 23 | Manualshive

Page: 23 / 64

background image

Publication 2364F-5.05 - March 1999

Troubleshooting Faults and Warnings

3-5

Troubleshooting Faults and
Warnings

The following list provides information for understanding and trouble-
shooting each fault or warning condition in the RGU.

Parameters can be stored in the internal memory of a GPT or Series B HIM,
or can be stored and printed out using DriveTools software.

Important: Always record or store parameters before upgrading firmware

or replacing the main control board.

!

ATTENTION: Do not attempt to alter or modify any printed
circuit boards. Any attempt to alter or modify boards may result
in personal injury or property damage.

Number Fault

Indicates

Action

0

P174 bit 0

ROM Bad CRC

Program memory error detected.

Try restarting the RGU, verify that all connections to the main control
board are in place, and check the main control board for any obvious
damage or any debris which may be shorting circuitry. If necessary,
try reinstalling the firmware (or upgrade to the latest available
firmware). Replace the board and/or send the board in for repair if
the problem cannot be resolved.

1

P174 bit 1

RAM Error

RAM error detected.

Try restarting the RGU, verify that all connections to the main control
board are in place, and check the main control board for any obvious
damage or any debris which may be shorting circuitry. If necessary,
try reinstalling the firmware (or upgrade to the latest available
firmware). Replace the board and/or send the board in for repair if
the problem cannot be resolved.

2

P174 bit 2

BatRAM Err

Battery-backed RAM error detected.

Try restarting the RGU, verify that all connections to the main control
board are in place, and check the main control board for any obvious
damage or any debris which may be shorting circuitry. If necessary,
try reinstalling the firmware (or upgrade to the latest available
firmware). Replace the board and/or send the board in for repair if
the problem cannot be resolved.

3

P174 bit 3

DSP Load

Error detected while loading DSP program
memory at startup.

Try restarting the RGU, verify that all connections to the main control
board are in place, and check the main control board for any obvious
damage or any debris which may be shorting circuitry. If necessary,
try reinstalling the firmware (or upgrade to the latest available
firmware). Replace the board and/or send the board in for repair if
the problem cannot be resolved.

4

P174 bit 4

FPGA Load

Error detected while loading FPGA firmware
at startup.

Try restarting the RGU, verify that all connections to the main control
board are in place, and check the main control board for any obvious
damage or any debris which may be shorting circuitry. If necessary,
try reinstalling the firmware (or upgrade to the latest available
firmware). Replace the board and/or send the board in for repair if
the problem cannot be resolved.

5

P174 bit 5

Iq Foldback

W

The current is being limited due to high
heatsink temperatures.

The internal wiring may be at risk of overheating. Check that the
door fans are operating properly, and verify that the RGU is operating
at the appropriately derated current (see the specifications appendix
in 2364F-5.01). Verify that the RGU is not operating in overload for
an extended period of time.

Note:

‘W’ indicates that the condition is normally reported as a warning, rather than a fault.

«
...
21
22
23
24
25
...
»

Summary of Contents for Bulletin 2364F

































































Reviews:

No comments

Related manuals for Bulletin 2364F

Brand: Keiser Pages: 82

Brand: Keiser Pages: 4

Brand: PAT Pages: 44

Brand: Park Tool Pages: 4

Brand: Qlight Pages: 4

Brand: Rain Harvesting Pages: 2

Brand: Hach Pages: 456

Brand: KCI Pages: 2

Brand: KCI Pages: 60

Brand: Landoll Pages: 38

Brand: Guyatone Pages: 2

Brand: Cuisinart Pages: 159

DJ Laptop stand +tray

Brand: Power Dynamics Pages: 3

Brand: Baileigh Industrial Pages: 40

Tidland Performance Series

Brand: Maxcess Pages: 72

Brand: KW Hydraulik Pages: 36

Autohelm ST4000

Brand: Raymarine Pages: 79

Brand: Icare Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands