ALLEN & HEATH iDR10 Reference Manual Download Page 26 | Manualshive

Page: 26 / 43

background image

iLive Reference Guide – Hardware

Part 1 - 26

AP6526-1 iss.5

Module options – Digital audio networking cards

M-ACE

ACE

is the Allen & Heath 64 channel bi-directional audio

and control point-to-point link (does not provide audio networking).
The BRIDGE port enables an external control Network connection to
be tunnelled over the same CAT5 cable as the audio. The second

ACE port can provide a redundant backup using a second cable.

The

iDR-32

and

iDR-48

always uses ACE as the Surface to MixRack

(Port A) link. Fitting ACE to Port B can provided 64 channel signal
splitting between MixRacks. This module can also be fitted to the

iLive

and

iDR10

Port A as a single cable point-to-point alternative to

the separate Network and ES cables currently used. To connect to

T

Series

components ACE should be fitted to the

iLive

.

The Surface to MixRack audio link must always be fitted to Port A.
Do not Connect Port A to Port B or vice versa.

M-ES-V2

EtherSound

. This uses the more recent and smaller

AVDM circuit card to provide a 64 channel bi-directional audio
network compatible with equipment fitted with EtherSound (including
the earlier

iLive

RAB version). It can be used in the

RAB2

module

on

iLive

and

iDR10

, or to equip the

iDR-32

and

iDR-48

with

EtherSound digital audio networking.

M-ES-V1-BASE

EtherSound

. This provides a cost effective

upgrade to RAB2 for

iLive

users who already have older RAB

modules with ES cards fitted in existing

iLive

systems. The older

AVD ES card may be fitted to this carrier to make it useable in RAB2
or the

iDR-32

and

iDR-48

.

M-MMO

Mini Multi Out

provides several popular multi-

channel digital output formats in a single module. Typical
application is for recording, connection to personal monitoring
systems, and routing to a speaker processor.

ADAT

– Three 8-channel optical outputs allow up to 24 track

recording.

Aviom

– 16 channel personal monitoring

iDR expander

– Connect up to two iDR 8 channel output expanders

(iDR-out analogue or iDR-Dout digital AES, Spdif, Toslink). Can
provide a digital link into the iDR-8 or iDR-4 digital audio processor.
This output is also compatible with the

Hearbus

8 channel personal

monitoring interface.

Firmware version

1.7

provides full MMO functionality in the MixRack

Port B slot and limited capability fitted to RAB2 Port B in the

iLive

surface.

M-MADI

MADI

. Dual port 64 channel bi-directional MADI audio

interface. It is usual for this to be used for system expansion or

recording from the MixRack Port B, but it could be used in the

iLive

Port A for the Surface link so providing additional channels at the

Surface for recording via MADI.

ACE - Point to point

64 in, 64 out
Surface Port A link
MixRack Port B link
Can transport control
and audio over a single
CAT5 cable
Redundant capable
120m max

ES - Networking

64 in, 64 out
Surface Port A link
MixRack Port B link
64 track recording
100m max (dependent

on cable type)

MMO - Digital outputs

Mixrack Port B
RAB2 Port B
24 track recording
16 channel monitoring
Link to iDR

MADI - Networking

64 in, 64 out, thru
Surface Port A link
MixRack Port B link
64 track recording
Redundant capable
300m max

Older ES AVD card

These are ‘mini’ module options available to interface with popular
multi-channel digital audio and networking standards. They may be
fitted to:

iDR10

and

iDR0

RAB2

module Port A and Port B.

iDR-64

,

iDR-48,

iDR-32

and

iDR-16

Port B

iLive-80, 112, 144, 176

RAB2 Port A, only MMO in Port B.

They may not be fitted to the

R72, T80

or

T112

Surfaces.

«
...
24
25
26
27
28
...
»

Summary of Contents for iDR10












































Reviews:

No comments

Related manuals for iDR10

Brand: Nemco Pages: 13

Brand: Ecco Pages: 12

Brand: UMF Medical Pages: 12

AJSPD850P - P2 DECK

Brand: Panasonic Pages: 73

Brand: VBM Pages: 36

Brand: W&H Med Pages: 122

Tablet1000 Series

Brand: Hantek Pages: 98

Brand: Nabtesco Pages: 26

Brand: PAS Systems International Pages: 24

MARK V Alcovisor

Brand: PAS Systems International Pages: 20

Brand: PARRY Pages: 14

Brand: York Fitness Pages: 36

Brand: Qu-Bit Electronix Pages: 15

Brand: Panasonic Pages: 23

Brand: Tieline Pages: 359

TITAN 2967-033A

Brand: Yetter Pages: 20

Brand: Kanlux Pages: 4

Brand: Raytec Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands