background image

Alcatel-Lucent 

Last revised: 1 Dec 2009 

01RN0031_H0-30 

10)

 

SSU FCR demerits 

The "Inactive SSU Unlock" demerit value of 275 is supported on the 3600 MainStreet 
and 3600+ MainStreet nodes. This demerit value is raised on the inactive shelf and 
indicates that the inactive SSU (or Timing card) is not locked (aligned) with the active 
SSU (or Timing card). These demerits will help to prevent an activity switch before 
alignment is achieved between the shelves. 

An activity switch before the inactive/active SSUs are aligned could cause the 
3600 MainStreet multishelf peripheral to go out of service in the worst case. 

On the 3600+ MainStreet node, an activity switch before the inactive and active 
Timing cards are aligned could cause all the UCS and HSA cards to reset. 

11)

 

Alcatel

Lucent 5620 Network Manager reconcile required after node upgrade 

It is assumed that all 3600 MainStreet and 3600+ MainStreet nodes will be fully 
reconciled by the Alcatel

Lucent 5620 Network Manager after the node has been 

upgraded to Release 9.0 from any previous node release for which conversion is 
supported. 

12)

 

Reset of DSP cards after upgrade 

To cover the instances where DSP cards must be reset to enable new functionality, an 
alarm indicating that a maintenance reset of the card must be scheduled has been 
added 

 the text is "Maintenance Reset Req'd". The alarm is raised when Release 9.0 

becomes active, and the subcode of the alarm is the slot number. As well, DNIC, 
2B1Q and 27LC2 cards equipped with DPM modules must be reset after the Release 
9.0 upgrade to force the download of new DSP firmware. This does not apply to the 
DPM3 module (supported on the 27LC3 card). 

13)

 

GFC support in the 3600 MainStreet multishelf system 

In prior releases, GFC Order Wire could not be used in 3600 MainStreet multishelf 
systems because of architectural restrictions of the product. This continues to be the 
case in Release 9.0. In addition, many of the new features introduced on the GFC3 
cannot be used on 3600 MainStreet multishelf systems for the same architectural 
reasons. A list of these features follows: 

 Order 

Wire 

   Digital Tone Test 

 BERT 

 DS0 

Test 

Access 

Page 9 

Summary of Contents for 3600 MainStreet













Reviews: