Host sends:
[Dir] [01] [01] [E9] [Mask.] [Chk]
Coin s. responds:
[01] [00] [Dir] [00] [Chk]
ACK
Example of message string for coin selector(
address 2
) first output(
pin7
) is:
Host sends:
[02] [01] [01] [E9] [01] [12]
Coin s. responds:
[01] [00] [02] [00] [FD]
Latch out 1 -> ACK
6.5.2.9
Command 232 [hexE8], Perform self-test
IMPORTANT WARNING: send only after at least 2 seconds have elapsed from power-on or from reset command.
Coin selector responds to command with one or two bytes of data according to table 6.3. First byte is fault code and
second is optional data, usually representing fault sensor number(
from 1 to 3
).
Code
Fault
Optional data
Comment
0
2
3
6
18
33
34
255
OK No fault detected
Fault on inductive sensor
Fault on credit sensor
Fault on diameter sensor
Fault on reject sensor
Power supply out of limits
Temperature out of limit
Unspecified fault code
-
Sensor number
-
-
-
-
-
-
-
-
Control opto sensor 2
-
Control opto sensor 3
-
Optional
-
Table 6.3 Fault codes for AL55/66 coin selectors
Inductive sensor numbers are:
01 Upper inductive sensor
02 First lower inductive sensor
03 Second lower inductive sensor
Message format is:
Host sends:
[Dir] [00] [01] [E8] [Chk]
Coin s. responds:
[01] [01I02] [Dir] [Fault c.][Data opt.] [Chk]
Example of message string for coin selector(
address 2
) with no fault detected is:
Host sends:
[02] [00] [01] [E8] [15]
Coin s. responds:
[01] [01] [02] [00] [00] [FC]
No fault detected
Ex. of message string for coin selector (
addr. 2
) with first lower sensor fault detected is:
Host sends:
[02] [00] [01] [E8] [15]
Coin s. responds:
[01] [02] [02] [00] [02][02] [F7]
Fault on first lower sensor detected
6.5.2.10
Command 231 [hexE7], Modify inhibit status
With this command host is able to inhibit the acceptance of some or all coins.
Acceptance or inhibition is set with a two byte mask sent by host.
Bits from 0 do 15 determinate coin positions from 1 to 16. Positions are sent by coin selector during reading credit buffer
or error codes (
header 229
).
Number of coin channels in new ALBERICI coin selectors AL55/66 is same as number of position(
16
).
Message format is:
Host sends:
[Dir] [02] [01] [E7] [LSB Mask.] [MSB Mask.] [Chk]
Coin s. responds:
[01] [00] [Dir] [00] [Chk]
ACK
Example of message string to enable all position for coin selector(
address 2
) is:
Host sends:
[02] [02] [01] [E7] [FF] [FF] [16]
Coin s. responds:
[01] [00] [02] [00] [FD]
ACK
After that all programmed coins will be enabled. Command has no effect on coin position that are not programmed.
Initially coin channels could be programmed with acceptance enabled or disabled.
For coin selectors that are using only cctalk interface, all coins position must be initially inhibited!
6.5.2.11
Command 230 [hexE6], Request inhibit status
Coin selector responds with two byte data that corresponds to inhibit state mask for all 16 positions of coin. If bit value is
1 acceptance of coin in that position is enabled. If bit value is 0 coin is inhibited. Message format is:
Host sends:
[Dir] [02] [00] [E6] [Chk]
Coin s. responds:
[01] [02] [Dir] [00] [LSB Mask.] [MSB Mask.] [Chk]
Example of message string for coin selector(
address 2
)
AL06V-c
(Coin selector for Italian gambling machines) after
power-up or reset is:
Summary of Contents for AL66 FG ARM Pulse
Page 1: ...AL66 FG ARM Pulse mod ccTalk COIN ACCEPTOR Operator s Manual Rev 2 01 User Manual...
Page 2: ......
Page 34: ......
