Akura SaorView AVT8010, User Manual

Page: 16 / 20

15
33
Configuration. Cont…
Low Power.
Selecting “Yes”, will activate the “low power” mode.
In standby the power will be less than 1W. The front
panel will show no information, except the standby
led.
Favourite Mode.
This function “Enables” or “Disables” the “Favourite
mode”. Use the
► / ◄ buttons to select.
Channel List.
Use the ► / ◄ buttons to select the item in the list.
“TV Only”. This will allow you to only view the TV
channels in memory.
“Radio Only”. This will allow you to only view the
Radio channels in memory.
“Text only”. This will allow you to only view the Text
channels in memory.
“View all” Default. This allows you to see all the
items in the memory. Use the PR+/PR- buttons to
navigate the list. To save any changes and Exit
press “MENU”. To exit without saving, press Exit.
Active Antenna.
The setting is “OFF” as default. If you need to use a
“mast head” amplifier to amplify the antenna signal,
this should be turned “ON”.
Note :- The STB can
supply 5V DC @ 30 m/a. Do not short circuit the
Antenna connector while activated. This may
damage the STB.
Auto Power Down.
If this is activated and No Function is performed
after 3 hours, the STB will automatically switch to
standby.
“No Function” = no Remote control
command or button press.
If the Auto power down is activated and you have
Record Timers set, you MUST turn the Auto Power
Down OFF.
Receiver Upgrade.
To ensure the STB has the most “up to date”
software, ensure the STB is set to “standby”. If an
upgrade is available, at 3am each day a
transmission will take place. The STB will “wake up”
and receive the upgrade automatically. This
normally takes up to 30 minutes.
Configuration. Cont…
If you have a Recording timed for 3am, then turn
the Auto Upgrade Off using the
► / ◄ buttons.
If you have not upgraded the software for some
time, use the
▲ / ▼ buttons to select “Scan for
Upgrade” and press OK. If there is an upgrade the
STB will download it…
note :- this may take up to
30 mins.
Do not forget to re enable the “Auto Upgrade” after
your programme is recorded.
Audio settings
Digital Audio Output.
Use the ▲ / ▼ buttons to select, and the ► / ◄
buttons to select PCM or Compressed. The default
is PCM.
If the transmission is in AC3 mode, select this and
turn it ON (Off is default).
Audio Delay.
When using an external Audio amplifier connected
via the “Optical Audio Connection” you may need to
“Delay” the audio to regain “Lip sync”. Select the
delay value to obtain correct lip sync.
Note :- If using PCM/AC3 you must have a suitable
Audio amplifier.
Video settings.
* TV Type.
The Output from your STB may be set to match
your TV type. Older TV’s display a 4 : 3 format,
while modern TV’s are usually 16 : 9 (wide screen).
To change the settings of the STB to match an
alternative TV that has been connected, select
“Video Settings”.
Use the
▲ / ▼ buttons to select the function and the
► / ◄ buttons to select the required setting.
TV Type
. Select from 4 : 3 or 16 : 9
Display Format
. Select from Full or Pillarbox.
TV Out.
Select from RGB and CVBS. RGB is the
better quality for modern TV’s. CVBS is less quality
for older TV’s.
HDMI Resolution
. Select from HDMI 1080i, 720p
560p. Check the resolution of your TV before
choosing.
To save your settings press “Menu” and the STB
will save and exit the settings. To exit without
saving, press Exit.
Parental Control.
Select “Parental Control” and press OK.
You will need to enter your PIN number (0000
default).
Maturity Lock
. You may select the age at which a
programme may be viewed. Use the ► / ◄ buttons
to select the required age, from 4 to 18 years.
7. Menu System