1454H502 Ed.03
Alarm delay
These delays prevent the display of specific alarms while allowing the unit to recover normal operation after certain
events.
-Delays in start-up (
A08
): Delays the activation of the alarms upon receiving power supply (start-up or after a
fault in the power supply). This allows starting up the installation avoiding constant alarm statuses.
-Alarm delay (
A07
): It delays the activation of the high and low pressure alarms (
A03
and
A05
) from the time
that the programmed values are reached.
-Turn-on delay time of alarms due to digital input 5 (
I09
): It delays the activation of activated alarms due to
digital input 5. The type of alarm to be activated depends on the configuration of parameter
I07
. It does not take
effect if parameter
I07
is set to 2 (Thermal alarm).
-Turn-on delay time of alarms due to digital input 6 (
I10
): It delays the activation of activated alarms due to
digital input 6. The type of alarm to be activated depends on the configuration of parameter
I08
. It does not take
effect if parameter
I08
is set to 2 (Thermal alarm).
7.5.- Remote disconnection
This function allows stopping / starting regulation with an external signal via the digital input 5 or 6.
The digital input 5 or 6 must be configured as a remote disconnection (
I07
or
I08
=5).
When stopping or starting regulation, the compressors / stages and fans will stop or start in accordance with the
timings set in parameters
t01
to
t08
.
8.- Connectivity
The
AKO-14545-C
model has a port for connection of RS485 (MODBUS) data, that allows remotely managing them
using a PC with the
AKONet
software or an
AKO-5011
server.
A different address must be assigned to each unit on the same network. This address is defined by parameter
P5
.
Other AKO equipment
with comunications
AKO-80039
PC +
AKONet
Tr-
Gnd
Tr+
AKO-5011
LAN
26 27 28
AKO-14545-C
ESC
?
SET
AKOCAM
Alarm delay
These delays prevent the display of specific alarms while allowing the unit to recover normal operation after certain
events.
-Delays in start-up (
A08
): Delays the activation of the alarms upon receiving power supply (start-up or after a
fault in the power supply). This allows starting up the installation avoiding constant alarm statuses.
-Alarm delay (
A07
): It delays the activation of the high and low pressure alarms (
A03
and
A05
) from the time
that the programmed values are reached.
-Turn-on delay time of alarms due to digital input 5 (
I09
): It delays the activation of activated alarms due to
digital input 5. The type of alarm to be activated depends on the configuration of parameter
I07
. It does not take
effect if parameter
I07
is set to 2 (Thermal alarm).
-Turn-on delay time of alarms due to digital input 6 (
I10
): It delays the activation of activated alarms due to
digital input 6. The type of alarm to be activated depends on the configuration of parameter
I08
. It does not take
effect if parameter
I08
is set to 2 (Thermal alarm).
7.5.- Remote disconnection
This function allows stopping / starting regulation with an external signal via the digital input 5 or 6.
The digital input 5 or 6 must be configured as a remote disconnection (
I07
or
I08
=5).
When stopping or starting regulation, the compressors / stages and fans will stop or start in accordance with the
timings set in parameters
t01
to
t08
.
8.- Connectivity
The
AKO-14545-C
model has a port for connection of RS485 (MODBUS) data, that allows remotely managing them
using a PC with the
AKONet
software or an
AKO-5011
server.
A different address must be assigned to each unit on the same network. This address is defined by parameter
P5
.
+
RS-485
GND
17
Summary of Contents for AKO-14545
Page 27: ...1454H502 Ed 03 27...
