AJA KONA 4 Installation And Operation Manual Download | Manualshive

Page: 77 / 89

background image

KONA Capture, Display, Convert v15.2 77 www.aja.com

Power

• 22W typical, 24W maximum

Environment

• Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F)
• Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140

degrees F)

• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)

KONA 1 Tech Specs

Video Formats

•  (2K) 2048 x 1080p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
•  (2K) 2048 x 1080PsF 23.98, 24, 25
•  (HD) 1080i 50, 59.94, 60
•  (HD) 1080PsF 23.98, 24, 25, 29.97, 30
•  (HD) 1080p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
•  (HD) 720p 50, 59.94, 60
•  (SD) 625i 50
•  (SD) 525i 59.94

Video Input Digital

• 3G-SDI, SMPTE-259/292/296/424

Video Output Digital

• 3G-SDI, SMPTE-259/292/296/424

Audio Input Digital

• 16-Channel 24-bit SDI embedded, 48 kHz synchronous

Audio Output Digital

• 16-Channel 24-bit SDI embedded, 48 kHz synchronous

Reference / LTC Input

• Analog Color Black or HD Tri-level sync
• LTC

Electrical Interface

• 2-lane PCIe 2.0

«
...
75
76
77
78
79
...
»

Summary of Contents for KONA 4


























































































Reviews:

No comments

Related manuals for KONA 4

Brand: IEI Technology Pages: 21

Brand: Xinje Pages: 57

Brand: Paradox Pages: 4

Brand: Yamaha Pages: 24

Brand: Yamaha Pages: 5

Brand: M86 Security Pages: 46

Brand: NEC Pages: 6

BLKDP45SG - MB 1333FSB DDR3 1333 Aud+Lan RAID SATA ATX

Brand: Intel Pages: 86

CNPS7000C Series

Brand: ZALMAN Pages: 8

Zypad WL15 Series

Brand: Eurotech Pages: 2

Brand: S&T Pages: 28

Brand: Kordis Pages: 31

Brand: WiebeTech Pages: 8

Brand: M86 Security Pages: 512

Brand: Altronix Pages: 8

StorageWorks TM RAID Array 3000 Pedestal Storage Subsystem

Brand: Compaq Pages: 112

Brand: ICP DAS USA Pages: 9

Brand: MSI Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands