AJA KONA 4 Installation And Operation Manual Download

Page: 64 / 89

KONA Capture, Display, Convert v15.2 64 www.aja.com

SDI Output Screen in 4K Mode

Figure 41. SDI Out Screen with 4K Format

Besides the general settings described in

"SDI Output Screen" on page 40

additional 4K related settings on this screen include:

4K Transport (KONA 5 or KONA 4 in 4K Mode)

Sets the 4K output transport. Select from:

• Auto - Automatically selects the transport, based on the input or selected

format.

• 4K-2SI - Sets 2SI output, using multiple links
• 1x 4K-12G (KONA 5 only) - Single link 12G output, which will also automatically

be downconverted and routed to the SDI 4 output.

•  2x 4K-Quad - Dual Link 4K/UltraHD output, SQD
•  4x 4K-Quad - Quad Link , SQD
•  1x 4K-Quarter - Downconverts the 4K/UltraHD signal to HD

NOTE: The 4K Transport setting also affects the HDMI output of the KONA card, even if

the SDI inputs are not being used. A SMPTE 2Si setting is required for UltraHD/4K

HDMI output. Other 4K Transport settings will downconvert HDMI output to HD

or 2K.

Summary of Contents for KONA 4


























































































Search results

Summary of Contents for KONA 4

Reviews:

Related manuals for KONA 4

Brands by name

Popular brands

AJA KONA 4, Installation And Operation Manual

Search results

Summary of Contents for KONA 4

Reviews:

Related manuals for KONA 4

Brands by name

Popular brands