AJ 1000M Operations Manual & Parts List Download Page 16

Page: 16 / 83

∎ Stop operation as soon as hose vibrate excessively.

Excessive vibration of high and low-pressure hoses of breaker calls for an instant disassembly and

repair. Contact the nearest service station appointed by AJCE. For caution’s sake, check oil leakage

at the back head. The operator is required to pay attention to follow points during operation.

∎ Greasing

With breaker mounted on carrier, apply down pressure on the chisel and fill the cavity with

recommended grease through the grease nipple.

∎ When operating the breaker, you must use ear and body protection.

You must use ear and breathing protection when the breaker is operating.

∎ Accumulator type - Danger

Pay Attention to pressurized container! Do not open without reading the manual or consulting with

the authorized service personnel.

∎ Do not touch chisel while breaker is working.

While the breaker is working, high temperature of the chisel will be generated.

Summary of Contents for 1000M




















































































Search results

Summary of Contents for 1000M

Reviews:

Related manuals for 1000M

Brands by name

Popular brands

AJ 1000M, Operations Manual & Parts List

Search results

Summary of Contents for 1000M

Reviews:

Related manuals for 1000M

Brands by name

Popular brands