AJ 1000M Operations Manual & Parts List Download Page 10 | Manualshive

Page: 10 / 83

background image

  ∎  Insert  3-way  valve  after  its  handle  is  fully  turned  counterclockwise.
  ∎  Turn  the  3-way  valve  handle  clockwise  slowly.  Stop  turning  it  when  the
      needle  of  the  gauge  starts  to  move.  If  it  is  turned  clockwise  too  tightly,
      the  valve  may  easily  be  damaged.  Pay  special  attention  to  ensure  that
      the  nitrogen  gas  is  not  charged  excessively.

ONLY FILL WITH N

2

GAS!

GAS CHARGE PRESSURE : 6.8kg/㎠(97 PSI)

CAUTION - THIS VESSEL CONTAINS HIGH PRESSURE GAS.

REMOVE REMAINING GAS BEFORE DISASSEMBLY.

ONLY FILL WITH N

2

GAS!

GAS CHARGE PRESSURE : 16.5kg/㎠(235 PSI)

CAUTION - THIS VESSEL CONTAINS HIGH PRESSURE GAS.

REMOVE REMAINING GAS BEFORE DISASSEMBLY.

∎ Back head sticker symbol
- Appears on the back head charging valve

«
...
8
9
10
11
12
...
»

Summary of Contents for 1000M




















































































Reviews:

No comments

Related manuals for 1000M

Signature Series

Brand: Balcrank Pages: 12

Brand: Tanco Pages: 26

Brand: Fein Pages: 133

Brand: Makita Pages: 16

Brand: P.I.T. Pages: 25

Brand: OTTENSTEN Pages: 30

MEAN WELL MDR Series

Brand: Simpex Electronic Pages: 4

Brand: Aprimatic Pages: 2

Brand: Gude Pages: 20

Brand: Agilent Technologies Pages: 47

Brand: Far Tools Pages: 17

Brand: Laguna Tools Pages: 8

Brand: Wixey Pages: 8

Brand: U-Line Pages: 12

Brand: Goobay Pages: 4

CH 601 XL ZODIAC 2002

Brand: Zenair Pages: 69

Brand: Gardebruk Pages: 19

Brand: YATO Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands