en
10
11
Battery must be inserted correctly to avoid damaging to the remote control. Always remove the
battery when the remote control will not be used for a long period of time, as this may cause
leakage of the battery and subsequently damage the remote.
Note:
•
When the display shows the hour it means
that the tower speaker is on standby mode
.
POWER ON & STAND BY MODE
1.
Once the tower speaker has been connected
to a wall outlet, turn on the main power
ON/OFF
button located at the back of the
unit, then the LED display will flash showing
the hour
00:00
.
2.
Press the
/SOURCE
button on the top panel
of the unit, or on the remote control to
initiate the function modes.
3.
To put the tower speaker in stand by mode,
just press the
/SOURCE
button on the top
panel of the unit, or on the remote control
and the display will show the time again.
MUTE
(On remote control only)
You can also press the
MUTE
button on the
remote control to turn off the sound.
Press the
MUTE
button again to cancel the
mute function and restore the sound.
The mute function will also be cancelled
automatically by pressing the
VOL +
or
VOL -
buttons or by turning the volume
ENCODER
of the top panel of the speaker.
BATTERY INSTALLATION
BASIC OPERATION
BATTERY INSTALLATION
Unscrew the battery cover and remove the battery holder. Insert a
CR-2025 TYPE
battery
(included) with polarities as shown,
then push the battery holder back into the remote and
screw the cover back on.
POWER OFF
1.
To turn the tower speaker off completely it
has to be done from a standby position,
then press the main power
ON/OFF
switch
located at the back of the unit, and the LED
display will switch off.
2.
Finally, you can unplug the device from the
wall outlet safely.
DIMMER ADJUSTMENT
(On remote control only)
Press repeatedly the
DIM+
or
DIM-
buttons on
the remote control to adjust the brightness of
the display and ambient lamp.
SOURCE
Press the
SOURCE
button repeatedly to
switch among
BT
(
Bluetooth
)
/ rAD
(Radio)
/ LINE
(Line in)
/ Cd
(CD)
/ USb
(USB)
/
CArD
(SD card) modes.
VOLUME LEVEL
Turn the volume
KNOB
on the top panel
or press the
VOL +
or
VOL -
buttons on the
remote control to adjust the volume level.
EQ (EQUALIZER)
(On remote control only)
Press the
EQ
button on the remote control
during any play mode to scroll through the
following equalizer settings:
Rock-Pop-Jazz-
Classic-Flat
.
REPEAT
Press repeatedly the
ALARM/REPEAT
button on the top panel of the unit, or
REP
on the remote control to scroll through the
following repeating settings:
One-All-OFF
.
SLEEP
(On remote control only)
Press repeatedly the
SLEEP
button on the
remote control to scroll through the following
sleep mode settings:
90-80-70-60-50-40-
30-20-10-OFF
.
Notes:
•
If the distance required between the remote control and the appliance decreases, the batteries
are exhausted. In this case replace the batteries with new ones.
•
The main power button on the back of the main unit must be ’ON‘ for the remote control to
operate.
STAND INSTALLATION
DETACHABLE STAND INSTALLATION
1.
Attach the base to the body aligning the four holes in the base and pillars with the four holes in the tower.
2.
Screw the base into the body.
3.
Attach the four pads to the base to protect the ground
(1pc for spare parts)
.
4.
Lift the tower upright on the floor. The Tower Speaker is now ready for use.
Notes:
•
Unplug the power cord from the wall outlet to protect your set during heavy thunderstorms.
•
The power cord is used to disconnect the device, the power cord should remain easily accessible.
Note:
•
The tower speaker cannot access the contents in the connected external device
.
CONNECTIONS
MAINS CONNECTION
1.
Check if the power voltage shown on the rating label located on the back of the set, corresponds
to your local AC power supply.
2.
Connect the power cord to the wall outlet.
USB CHARGING PORT
C
onnect an external device (e.g. smartphone, mp3 player) via a USB cable
(not provided)
to the
USB
CHARGING
port.
