background image

6

Fault Checkup

Please check the following when consigning repair service:

                     Symptoms                                                     Reasons

All these  are not problems

•  Water flow sound

Water flow sound can be heard when starting operation, 

during operation or immediately after stopping operation. 

When it starts to work for 2-3 minutes, the sound may 

become louder, which is the flowing sound of refrigerant or 

the draining sound of condensed water.

•  Cracking sound

During operation, the air conditioner may make the 

cracking sound, which is caused from the temperature 

changes or the slight dilation of heat exchanger.

•  Terrible smell in outlet air

•  Flashing operating 

indicator

When switching it on again after power failure, turn on the 

manual power switch and the operating indicator flashes.

•  Awaiting indication 

It displays the awaiting indication as it fails to perform 

refrigerating operation while other indoor units are 

in heating operation. When the operator set it to the 

refrigerating or heating mode and the operation is opposite 

to the setting, it displays the awaiting indication.

•  Sound in

•  shutdown indoor 

•  unit or white 

•  steam or cold air

To prevent oil and refrigerant from blocking the shutdown 

indoor units, refrigerant flows in the short time and make 

the sounds of refrigerant flowing. Otherwise, when other 

indoor units performs heating operation, white steam may 

occur; during refrigerating operation, cold air may appear.

When the conditioner is powered on, the sound is made 

due to the resetting of the expansion valve.

Check if it is in the state of Timer-ON and Timer-OFF.

•  Failure to work

Check if there is a power failure.

Check if the manual power switch is turned off.

Check if the supply fuse and breaker are disconnected.

Check if the protective unit is working.

Check if refrigerating and heating functions are selected 

simultaneously with the awaiting indication on line control.

•  Bad cooling & heating 

effects

Check if air intake port and air outlet port of outdoor units are 

blocked.

Check if the door and windows are open.

Check if the filtering screen of air cleaner is blocked with 

sludge or dust.

Check if the setting of wind quantity is at low wind.

Check if the setting of operation is at the Fan Operation state.

Check if the temperature setting is proper.

During operation, the air conditioner may make the cracking 

sound, which is caused from the temperature changes or 

the slight dilation of heat exchanger.

Under the following circumstances, immediately stop the operation, disconnect the manual 

supply switch and contact the after-service personnel. 

•  When buttons are inflexible actuated;

•  When there are foreign objects and water in the refrigerator;

•  When it cannot still be operated after removing the operation of protective unit;

•  When other abnormal conditions occur.

Please make another check.

•  Clicking sound when 

switching the air condition 

on

•  Start or stop working 

automatically

Summary of Contents for AWSI-DDV007-N11

























Reviews: