background image

5

Maintenance

Before Operating Season:

1. Please make the following checkup. If abnormal condition occurs, consult the after-service     

    personnel.

•  There is no blockage in inlet port and outlet port of outdoor and indoor units.

•  The ground line and the wiring are in the proper state

2. After cleaning, the air cleaner must be mounted.

3. Switch on to the power.

After Operating Season:

1.  In sunny days, blowing operation can be performed for half a day to make the inside of       

     machine dry.

2. Electrical power should be cut down to economize electricity, or the machine will still           

     consume power.Air cleaner and shell must be mounted after cleaning.

Maintenance before and after Operating Season

Clean the air cleaner & air inlet grid.

•  Don't dismantle the air cleaner if not cleaning, or faults might be caused.

•  When the air conditioner operates in the environment with too much dust, clean the air 

conditioner more times (generally once every two weeks).

•  Do not wipe the wind deflector with water forcibly to avoid falling off.

Cleaning Wind Deflector:

Cleaning the air outlet port and the shell:

       

Attention

•  Don't use gasoline, benzene, diluents, polishing powder or liquid insecticide to clean them.

•  Do not clean them with hot water of above 50  to avoid fading or distorting.

•  Wipe them with soft dry cloth.

•  Water or neutral dry cleanser is recommended if the dust cannot be removed.

•  The Wind Deflector can be dismantled to clean (as below).

•  Wipe dust with water or dust collector. 

   (A) Wipe dust with dust collector.

(B) Clean it with soft bush in mild detergent         

if there is too much dust on it

(C)Throw off the water and airing it  

   in the cool dry condition.

Cleaning Air Cleaner:

      

Attention

•  Don't rinse the air cleaner with hot water of above 50  to avoid fading and distorting.

•  Don't put the air cleaner on the fire to dry to avoid catching fire.

Summary of Contents for AWSI-DDV007-N11

























Reviews: