background image

En-4

Installation method of Drain cap

 Please put the heat insulation inside all along.

 Use a hexagonal wrench (4mm at opposite side) to insert the drain cap, till the drain 

cap contacts the tip of drain cock.

No gap

Hexagonal 
wrench

Drain Cock

Drain cap

Insulation

No gap

[Removal method of drain hose]

Remove the screw at the left of drain hose and pull out drain hose.

Drain 

fi

 xture (blue)

Screw

Drain hose

[Installation method of drain hose]

Vertically insert the drain hose toward the inside, so that the drain 

fi

 xture (blue) can 

accurately align with the screw hole around the drain cock.

After inserting and before replacing, please reinstall and 

fi

 x the removed screws.

Drain cock

Screw

Drain hose

Drain 

fi

 xture (blue)

Screw hole

  Be sure to install around the drain hose connector.
  As the screw is inside, be sure to use screwdriver treated with magnet.

3.3.5. Installing the indoor unit

(1)  After passing the indoor piping and drain hose through the wall hole, hang the indoor 

unit on the hooks at the top and bottom of the wall hook bracket.

Wall hook bracket

Top hooks

Indoor unit

(Fitting)

Bottom hooks

Connection pipe
(2 mm dia.)

(2)  Remove the intake grille.

1

  Open the intake grille.

2

2

1

1

Intake grille

2

  Pull down the knob.

Knob

Intake grille

3

  Lift the intake grille upward, until the axle at the top of the intake grille is removed. 

(3)  Remove the front panel.

1

  The thumb is hung on the lower part as shown in the 

fi

 gure, and it pulls to the 

front, pushing [

] mark, and bottom hooks (2 position) is removed from wall hook 

bracket.

2

  The front panel bottom is pulled to the front, and bottom hooks is removed indoor 

unit.

Screws 
(4 position)

Push

[

mark

Push

Wall hook bracket

Front panel

3

  The front panel is pulled to the front, raising the upper surface, and a front panel 

is removed.

Front panel

(4)  Insert the spacer, etc. between the indoor unit and the wall hook bracket and 

separate the bottom of the indoor unit from the wall.

Wall hook bracket

Indoor unit

Spacer

4.

 

PIPE INSTALLATION

 

CAUTION

  Be more careful that foreign matter (oil, water, etc.) does not enter the piping than with 

refrigerant R410A models. Also, when storing the piping, securely seal the openings 
by pinching, taping, etc.

  While welding the pipes, be sure to blow dry nitrogen gas through them.

4.1. Selecting the pipe material

 

CAUTION

  Do not use existing pipes from another refrigeration system or refrigerant.

  Use pipes that have clean external and internal sides without any contamination which 

may cause trouble during use, such as sulfur, oxide, dust, cutting waste, oil, or water.

  It is necessary to use seamless copper pipes.
  Material : Phosphor deoxidized seamless copper pipes
  It is desirable that the amount of residual oil is less than 40 mg/10 m.

  Do not use copper pipes that have a collapsed, deformed, or discolored portion 

(especially on the interior surface). Otherwise, the expansion valve or capillary tube 
may become blocked with contaminants.

  Improper pipe selection will degrade performance. As an air conditioner using R410A 

incurs pressure higher than when using conventional (R22) refrigerant, it is necessary 
to choose adequate materials.

• 

Thicknesses of copper pipes used with R410A are as shown in the table.

• 

Never use copper pipes thinner than those indicated in the table even if they are 
available on the market.

Thicknesses of Annealed Copper Pipes (R410A)

Pipe outside diameter [mm (in.)]

Thickness [mm]

6.35 (1/4)

0.80

9.52 (3/8)

0.80

12.70 (1/2)

0.80

15.88 (5/8)

1.00

19.05 (3/4)

1.20

4.2. Pipe requirement

 

CAUTION

  Refer to the installation manual for the outdoor unit for description of allowable pipe 

length and height difference.

  Use pipe with water-resistant heat insulation.

9373370192_IM.indb   Sec1:4

9373370192_IM.indb   Sec1:4

2/16/2013   11:13:08 AM

2/16/2013   11:13:08 AM

Summary of Contents for ASHA04GACH
















Reviews: