Airspan 605-0000-742 Hardware Installation Download Page 44

Page: 44 / 83

605-0000-742_MicroMAX_Hardware_Installation_Rev_G

MOUNTING THE GPS

Mounting the GPS

Depending on individual customer requirements and environmental influences, there are several
available options for mounting the GPS:

Pole Mounting: Using the 1" – 14 threads, the GPS can be mounted onto a standard

antenna mast or mounting adapter. (not supplied)

Mounting Plate: Using three 10-32 UNF screws, the GPS can be mounted on a flat surface

with three holes on a 1.75-inch diameter circle. (not supplied)

Direct Mounting: The unit may be mounted directly to a suitable structure that has been

provided with holes suited to the GPS mounting details.

Pole Mounting

Note:

When mounting the GPS on a metal pole that is in physical contact with the ground,

the GPS will not synchronize. To enable synchronization, you need to isolate the GPS from the

pole using isolation material.

Summary of Contents for 605-0000-742




















































































Search results

Summary of Contents for 605-0000-742

Reviews:

Brands by name

Popular brands

Airspan 605-0000-742, Hardware Installation

Search results

Summary of Contents for 605-0000-742

Reviews:

Brands by name

Popular brands