Airspan 605-0000-742 Hardware Installation Download Page 18

Page: 18 / 83

PHYSICAL DESCRIPTION

This section provides a description of the components of the MicroMAX installation:

MicroMAX

(outdoor unit)

SDA-4S Type II

(indoor unit)

SDA-4SDC Type II

(indoor DC unit)

MicroMAX BSR

The BSR is an encased outdoor radio providing access to communication ports on its bottom panel.

The BSR's back panel provides holes for mounting.

Physical Dimensions

The table below lists the physical dimensions of the BSR.

Parameter Value

Comment

Height

400 mm (15.74 inches)

Width

317 mm (12.48 inches)

Depth

65.5 mm (2.58 inches)

Weight 3.8

The physical dimensions exclude the mounting kit.

The figure below illustrates the MicroMAX's physical dimensions.

Note:

BSR models that use third-party external antennas provide an N-type receptacle for

attaching an external antenna.

Summary of Contents for 605-0000-742




















































































Search results

Summary of Contents for 605-0000-742

Reviews:

Brands by name

Popular brands

Airspan 605-0000-742, Hardware Installation

Search results

Summary of Contents for 605-0000-742

Reviews:

Brands by name

Popular brands