Airmar 300WXR, 300WX, 150WX, 100WX w/CAN,100WX Technical Manual Download Page 20

Page: 20 / 90

WX Series WeatherStation Technical Manual revision 1.000

Proprietary and Confidential

PRELIMINARY - DRAFT

<18>

N = knots

<19>

Wind speed, meters per second, to the nearest 0.1 m/s

<20>

M = meters per second

Notes

This WX Series WeatherStation Sensor has a relative humidity sensor.

The barometric pressure provided in this sentence is the

altimeter setting

, which is

the barometric pressure corrected for altitude above sea level. See the transmitted

$YXXDR(A) sentence, and the received $PAMTC,ALT command, for further

information.

Summary of Contents for 300WXR, 300WX, 150WX, 100WX w/CAN,100WX



























































































Search results

Summary of Contents for 300WXR, 300WX, 150WX, 100WX w/CAN,100WX

Reviews:

Related manuals for 300WXR, 300WX, 150WX, 100WX w/CAN,100WX

Brands by name

Popular brands

Airmar 300WXR, 300WX, 150WX, 100WX w/CAN,100WX, Technical Manual

Search results

Summary of Contents for 300WXR, 300WX, 150WX, 100WX w/CAN,100WX

Reviews:

Related manuals for 300WXR, 300WX, 150WX, 100WX w/CAN,100WX

Brands by name

Popular brands