Airmar 300WXR, 300WX, 150WX, 100WX w/CAN,100WX Technical Manual Download Page 13

Page: 13 / 90

WX Series WeatherStation Technical Manual revision 1.000

Proprietary and Confidential

PRELIMINARY - DRAFT

NMEA 0183 TRANSMITTED SENTENCE

$GP

GLL

$PAMTC,EN:

GLL

Default Interval (m:ss.00)

0:1.00

Enabled By Default:

Summary

NMEA 0183 standard Geographic Position – Latitude/Longitude.

Syntax

$GPGLL,<1>,<2>,<3>,<4>,<5>,<6>,<7>*hh<CR><LF>

Fields

<1>

Latitude, to the nearest .0001 minute

<2>

N if field <1> is North Latitude

S if field <1> is South Latitude

<3>

Longitude, to the nearest .0001 minute

<4>

E if field <3> is East Longitude

W if field <3> is West Longitude

<5>

UTC of position, in the form hhmmss

<6>

Status:

A = data valid; V = data invalid

<7>

Mode indicator:
A = Autonomous mode

D = Differential mode

E = Estimated (dead reckoning) mode

M = Manual input mode

S = Simulator mode

N = Data not valid
The only values transmitted by the WX Series WeatherStation Sensor

for the Mode indicator are A, D, and N.

Notes

Summary of Contents for 300WXR, 300WX, 150WX, 100WX w/CAN,100WX



























































































Search results

Summary of Contents for 300WXR, 300WX, 150WX, 100WX w/CAN,100WX

Reviews:

Related manuals for 300WXR, 300WX, 150WX, 100WX w/CAN,100WX

Brands by name

Popular brands

Airmar 300WXR, 300WX, 150WX, 100WX w/CAN,100WX, Technical Manual

Search results

Summary of Contents for 300WXR, 300WX, 150WX, 100WX w/CAN,100WX

Reviews:

Related manuals for 300WXR, 300WX, 150WX, 100WX w/CAN,100WX

Brands by name

Popular brands